Difficulty
Moderate
Steps
23
Time Required
3 hours
Sections
4
- Battery
- 4 steps
- SSD/Hard Drive
- 4 steps
- Keyboard
- 6 steps
- Screen Module
- 9 steps
Flags
2
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
BackLenovo ThinkPad X230
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Preparations
- Before you begin, be sure to turn off your laptop and unplug it from the outlet.
Before you begin, be sure to turn off your laptop and unplug it from the outlet.
1024
Step 2
Locate the battery
- Flip the computer upside down.
- The red rectangle shows the location of the battery.
Flip the computer upside down.
The red rectangle shows the location of the battery.
Step 3
Unlock the left switch
- Locate the two switches that lock the battery. Push the left-hand switch outward into the “unlocked” position.
Locate the two switches that lock the battery. Push the left-hand switch outward into the “unlocked” position.
Step 4
Remove the battery
- Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer.
Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer.
Step 5
Locate the hard drive enclosure
- Locate the hard drive enclosure (marked by the red rectangle).
Locate the hard drive enclosure (marked by the red rectangle).
Step 6
Remove enclosure
- Use a small Phillips screwdriver to unscrew the single screw that holds down the hard drive enclosure cover.
- The screw is designed to remain within the plastic cover. Don’t worry about extracting it completely.
- Carefully remove the hard drive enclosure cover.
Use a small Phillips screwdriver to unscrew the single screw that holds down the hard drive enclosure cover.
The screw is designed to remain within the plastic cover. Don’t worry about extracting it completely.
Carefully remove the hard drive enclosure cover.
Step 7
Remove SSD/hard drive
- Gently pull the black pull tab out from above the hard drive. Continue pulling on the pull tab until the hard drive and the two plastic rails come out of the enclosure.
- Pull on the tab firmly but slowly. The hard drive should come out of the enclosure effortlessly.
Gently pull the black pull tab out from above the hard drive. Continue pulling on the pull tab until the hard drive and the two plastic rails come out of the enclosure.
Pull on the tab firmly but slowly. The hard drive should come out of the enclosure effortlessly.
Step 8
Remove plastic rails
- Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive.
Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive.
Step 9
remove screws
- There are 2 screws securing the keyboard. You can identify them by a small keyboard symbol (marked by an orange rectangle in the second picture).
- Once you have located the two screws, remove them with a small Phillips screwdriver.
There are 2 screws securing the keyboard. You can identify them by a small keyboard symbol (marked by an orange rectangle in the second picture).
Once you have located the two screws, remove them with a small Phillips screwdriver.
Step 10
remove strip above keyboard
- This step is not required.
- Gently pull the strip out from the case.
This step is not required.
Gently pull the strip out from the case.
Step 11
pop keyboard out of the casing
- Use a a plastic spudger (or a flat screwdriver) to push the keyboard towards the screen. This will pop the bottom of the keyboard out of the casing.
Use a a plastic spudger (or a flat screwdriver) to push the keyboard towards the screen. This will pop the bottom of the keyboard out of the casing.
Step 12
lift keyboard
- Carefully lift the keyboard so that you can access its connector.
Carefully lift the keyboard so that you can access its connector.
Step 13
Unplug keyboard
- Carefully unplug the connector by pulling.
Carefully unplug the connector by pulling.
Step 14
done
- You are done - the keyboard is not connected to the laptop any more and can be replaced.
You are done - the keyboard is not connected to the laptop any more and can be replaced.
Step 15
Screen Module
- Remove five 5.7mm screws from the bottom.
Remove five 5.7mm screws from the bottom.
Step 16
- Unscrew two 5.7mm screws from the top of the bottom of the laptop.
Unscrew two 5.7mm screws from the top of the bottom of the laptop.
Step 17
- Pull the palm rest off the laptop board.
Pull the palm rest off the laptop board.
Step 18
- Unlock the white seal and disconnect the blue cable.
Unlock the white seal and disconnect the blue cable.
Step 19
- Carefully disconnect blue and red cables and remove them from plastic case.
Carefully disconnect blue and red cables and remove them from plastic case.
Step 20
- Unlock white seal and diconnect blue cable from upper corner.
Unlock white seal and diconnect blue cable from upper corner.
Step 21
- Remove two 4.1mm screws from the black frame.
Remove two 4.1mm screws from the black frame.
Step 22
- Carefully pull off black frame from laptop board.
Carefully pull off black frame from laptop board.
Step 23
- Carefully lift the screen module straight up to detach from board.
Carefully lift the screen module straight up to detach from board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 2 other contributors
Lino Virgen
Member since: 10/10/2016
884 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
Texas Tech, Team 6-3, Bennett Fall 2016
Member of Texas Tech, Team 6-3, Bennett Fall 2016
TTU-BENNETT-F16S6G3
4 Members
3 Guides authored
