Lenovo Thinkpad X100E Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Screen
10 steps

Flags

BackLenovo ThinkPad X100e
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Use a Spudger tool to remove the screw covers on each side of the screen.
Be sure not to lose screw covers.

Use a Spudger tool to remove the screw covers on each side of the screen.

Be sure not to lose screw covers.

1024

Step 2

Using a magnetic screwdriver fit with a PH0 Bit, unscrew the two screws and carefully set the aside.

Using a magnetic screwdriver fit with a PH0 Bit, unscrew the two screws and carefully set the aside.

Step 3

Pry open the bezel carefully with the spudger tool.
You will want to do this until the frame is completely off.

Pry open the bezel carefully with the spudger tool.

You will want to do this until the frame is completely off.

Step 4

Remove all exposed screws and carefully set them aside. There should be 6 visible screws.
Be sure to set the screws aside on the magnetic mat.

Remove all exposed screws and carefully set them aside. There should be 6 visible screws.

Be sure to set the screws aside on the magnetic mat.

Step 5

Lift the screen up carefully, and remove the screws on both sides of the panel. There should be 4 screws.
The other two screws are located in the exact place on the other side.
Don’t forget to place the screws on the magnetic mat, separate from other screws.

Lift the screen up carefully, and remove the screws on both sides of the panel. There should be 4 screws.

The other two screws are located in the exact place on the other side.

Don’t forget to place the screws on the magnetic mat, separate from other screws.

Step 6

Remove the connector located at the very top of the screen beside the webcam.
To remove the connector, simply pull the connector out.

Remove the connector located at the very top of the screen beside the webcam.

To remove the connector, simply pull the connector out.

Step 7

Fold the panel over until a strip of black tape is visible.
Peel the tape down until you get to the base.

Fold the panel over until a strip of black tape is visible.

Peel the tape down until you get to the base.

Step 8

Peel the piece of transparent tape back.
At this point there should be some exposed wires underneath the tape.

Peel the piece of transparent tape back.

At this point there should be some exposed wires underneath the tape.

Step 9

Remove the connector carefully with the spudger tool.

Remove the connector carefully with the spudger tool.

Step 10

Remove the black tape fully.
Now your device is ready for a new panel.

Remove the black tape fully.

Now your device is ready for a new panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Orly Guerra

Member since: 02/08/2018

448 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       University of North Texas, Team 1-13, Smith Spring 2022                        

                                                  Member of University of North Texas, Team 1-13, Smith Spring 2022 



                    UNT-SMITH-S22S1G13                     


                                            2 Members                     


                                            3 Guides authored

Keith Bowe - Jul 6, 2019

What can be used as a replacement screen, as it’s listed not for sale?

Introduction#

What you need#

Team#

Introduction

What you need

Team