Difficulty
Moderate
Steps
9
Time Required
8 - 15 minutes
Sections
4
- Back Cover
- 1 step
- Speakers
- 2 steps
- Battery
- 2 steps
- Display
- 4 steps
Flags
0
BackLenovo ThinkPad X1 Gen 1 Extreme
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The removal of the display requires you to first remove the battery, then proceed to remove the hinge covering, take off the display cover, and detach it from the motherboard. Make sure the device is turned off before you begin these steps.
What you need
Step 1
Back Cover
- Power off and unplug your device before you begin.
- Orient the laptop so that it is bottom up, and the trackpad is closest to you.
- Unscrew the seven captive screws with a Phillips #00 screwdriver.
- These screws will loosen, but stay attached to the cover. Do not attempt to completely remove them.
- Slide a blue opening pick in the gap between the bottom panel and chassis, and pry off the one clip on each side.
- Remove the back cover from the device.
Power off and unplug your device before you begin.
Orient the laptop so that it is bottom up, and the trackpad is closest to you.
Unscrew the seven captive screws with a Phillips #00 screwdriver.
These screws will loosen, but stay attached to the cover. Do not attempt to completely remove them.
Slide a blue opening pick in the gap between the bottom panel and chassis, and pry off the one clip on each side.
Remove the back cover from the device.
1024
Step 2
Speakers
- Use a Phillips #00 head screwdriver to remove the four 4 mm screws above the battery.
Use a Phillips #00 head screwdriver to remove the four 4 mm screws above the battery.
Step 3
- Lift the speaker modules on either side of the battery out of its pegs, and unwind the cable from the front of the battery.
- Set the speaker modules out of the way.
Lift the speaker modules on either side of the battery out of its pegs, and unwind the cable from the front of the battery.
Set the speaker modules out of the way.
Step 4
Battery
- Use tweezers to peel the plastic cover off the connector.
- Use a spudger or your fingernail to pry up the battery straight up from the motherboard.
Use tweezers to peel the plastic cover off the connector.
Use a spudger or your fingernail to pry up the battery straight up from the motherboard.
Step 5
- Lift the battery out of the frame and remove it from the device.
Lift the battery out of the frame and remove it from the device.
Step 6
Display
- Gently take off the cover of the hinge of the computer with a combination of the opening tool and your hands.
Gently take off the cover of the hinge of the computer with a combination of the opening tool and your hands.
Step 7
- Lift up the covering of the display using the opening tool.
Lift up the covering of the display using the opening tool.
Step 8
- Use a spudger to release the retaining flap on the cable connector.
Use a spudger to release the retaining flap on the cable connector.
Step 9
- Pull the wire that was connected to the retaining flap through the hinge.
- Remove the display from the laptop.
Pull the wire that was connected to the retaining flap through the hinge.
Remove the display from the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Ryleigh Jenkins
Member since: 09/21/2021
199 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
The Citadel Military College of South Carolina, Team 3-18, Eggleston Fall 2021
Member of The Citadel Military College of South Carolina, Team 3-18, Eggleston Fall 2021
CMCSC-EGGLESTON-F21S3G18
3 Members
2 Guides authored