Difficulty

Moderate

Steps

13

Time Required

                          1 hour

Sections

4

  • Back Cover
  • 3 steps
  • Battery
  • 2 steps
  • Motherboard
  • 6 steps
  • Keyboard
  • 2 steps

Flags

0

  • BackLenovo ThinkPad X1 Carbon 7th Gen

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back cover removal
  • Use a Phillips #1 screwdriver to loosen the five captive screws securing the back cover.

Use a Phillips #1 screwdriver to loosen the five captive screws securing the back cover.

1024

Step 2

              Insert an opening pick
  • Insert an opening pick at a 45˚ angle between the back cover and frame near the rear middle screw.
  • Pry up on the pick to release the clips securing the back cover to the frame.
  • You will hear several clicks while prying up.

Insert an opening pick at a 45˚ angle between the back cover and frame near the rear middle screw.

Pry up on the pick to release the clips securing the back cover to the frame.

You will hear several clicks while prying up.

Step 3

              Remove the back cover
  • Lift the back cover up and remove it from the chassis.
  • You will hear several clicks while lifting up.
  • During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.

Lift the back cover up and remove it from the chassis.

You will hear several clicks while lifting up.

During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.

Step 4

              Unfasten the battery
  • Use a Phillips #0 screwdriver to remove the six 4.9 mm-long screws securing the battery.

Use a Phillips #0 screwdriver to remove the six 4.9 mm-long screws securing the battery.

Step 5

              Remove the battery
  • Lift the battery straight out of its recess and remove it.

Lift the battery straight out of its recess and remove it.

Step 6

              Motherboard
  • Remove the connectors with bar latches by lifting up on the small bar behind the port and pulling the circuit ribbon away from the port.

Remove the connectors with bar latches by lifting up on the small bar behind the port and pulling the circuit ribbon away from the port.

Step 7

  • Remove the snap connectors by lifting straight up until the connection pops out.
  • Use an opening tool to pry them off if a finger cannot get underneath the connection.

Remove the snap connectors by lifting straight up until the connection pops out.

Use an opening tool to pry them off if a finger cannot get underneath the connection.

Step 8

  • Remove the latch connections by lifting the latch up, releasing the circuit ribbon.
  • Use an opening tool to get underneath the latch if a finger cannot.

Remove the latch connections by lifting the latch up, releasing the circuit ribbon.

Use an opening tool to get underneath the latch if a finger cannot.

Step 9

  • Remove the insert connections by pulling the connector away from the port.

Remove the insert connections by pulling the connector away from the port.

Step 10

  • Remove the seven 4 mm Phillips #0 screws that hold the motherboard in place
  • Remove the 3 mm Phillips #0 screw located near the fan.

Remove the seven 4 mm Phillips #0 screws that hold the motherboard in place

Remove the 3 mm Phillips #0 screw located near the fan.

Step 11

  • Lift the motherboard with the fan still connected straight up and out of the device.

Lift the motherboard with the fan still connected straight up and out of the device.

Step 12

              Keyboard
  • Using a Phillips #00 screwdriver, remove sixty-six 0.5 mm screws from the keyboard.

Using a Phillips #00 screwdriver, remove sixty-six 0.5 mm screws from the keyboard.

Step 13

  • Lift the keyboard straight up and out of the computer.

Lift the keyboard straight up and out of the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors 


                    Everett James Barkley

Member since: 09/16/2020

338 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       The Citadel Military College of South Carolina, Team S2-G13, Eggleston Fall 2020                        

                                                  Member of The Citadel Military College of South Carolina, Team S2-G13, Eggleston Fall 2020 



                    CMCSC-EGGLESTON-F20S2G13                     


                                            3 Members                     


                                            4 Guides authored