Difficulty
Moderate
Steps
14
Time Required
20 - 30 minutes
Sections
4
- Hard Drive
- 4 steps
- Keyboard
- 4 steps
- Upper Casing
- 4 steps
- Speaker
- 2 steps
Flags
0
BackLenovo Thinkpad Twist s230u
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Hard Drive
- Flip the laptop over.
- Using a Phillips #1 Screwdriver, unscrew the screw on the bottom left corner.
Flip the laptop over.
Using a Phillips #1 Screwdriver, unscrew the screw on the bottom left corner.
1024
Step 2
- Using the iFixit Opening tool, loosen the hard drive cover.
Using the iFixit Opening tool, loosen the hard drive cover.
Step 3
- Remove the hard drive cover.
Remove the hard drive cover.
Step 4
- Remove the hard drive by sliding it out.
Remove the hard drive by sliding it out.
Step 5
Keyboard
- Use a Philips #1 screwdriver to remove 2 screws on the bottom of the laptop.
Use a Philips #1 screwdriver to remove 2 screws on the bottom of the laptop.
Step 6
- Use a spudger to loosen the keyboard around the edges.
- Carefully push the keyboard towards the screen to unlatch it.
- Do not push too hard, as there are ribbon cables attached to the keyboard.
Use a spudger to loosen the keyboard around the edges.
Carefully push the keyboard towards the screen to unlatch it.
Do not push too hard, as there are ribbon cables attached to the keyboard.
Step 7
- Carefully lift up the keyboard to access the wires underneath.
- Be careful not to break the ribbon cables attached underneath.
Carefully lift up the keyboard to access the wires underneath.
Be careful not to break the ribbon cables attached underneath.
Step 8
- Open the small black flap on each of the ribbon cables. It should lift with a slight effort.
- Pull out the ribbon cables and remove the keyboard from the device.
Open the small black flap on each of the ribbon cables. It should lift with a slight effort.
Pull out the ribbon cables and remove the keyboard from the device.
Step 9
Upper Casing
- Flip your device over.
- Use the Phillips #1 screwdriver to remove the nine screws.
Flip your device over.
Use the Phillips #1 screwdriver to remove the nine screws.
Step 10
- Flip the device back over and open the top.
- Use the Phillips #1 screwdriver to remove the seven silver screws.
- Disconnect the three cables inside the case.
- Lift up the brown tab and disconnect the ribbon cable.
Flip the device back over and open the top.
Use the Phillips #1 screwdriver to remove the seven silver screws.
Disconnect the three cables inside the case.
Lift up the brown tab and disconnect the ribbon cable.
Step 11
- Close the lid and turn the device around.
- Use the iFixit Opening Tool to lift up and remove the tab on the back.
Close the lid and turn the device around.
Use the iFixit Opening Tool to lift up and remove the tab on the back.
Step 12
- Turn the device back around and reopen it.
- Use the iFixit Opening Tool to disconnect the top of the case from the bottom.
- Lift up the top of the case and slide it out from under the screen.
Turn the device back around and reopen it.
Use the iFixit Opening Tool to disconnect the top of the case from the bottom.
Lift up the top of the case and slide it out from under the screen.
Step 13
Speaker
- Flip the laptop cover over.
- Using a Phillips #1 Screwdriver, remove the four screws holding the speakers in.
Flip the laptop cover over.
Using a Phillips #1 Screwdriver, remove the four screws holding the speakers in.
Step 14
- Remove the speakers from the device.
Remove the speakers from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Arthur McPeak
Member since: 01/14/2020
664 Reputation
6 Guides authored
Badges:
9
+6 more badges
Team
Embry-Riddle Aeronautical University, Team S1-G3, Cromer Twal Spring 2020
Member of Embry-Riddle Aeronautical University, Team S1-G3, Cromer Twal Spring 2020
ERAU-CROMER TWAL-S20S1G3
3 Members
6 Guides authored
