Difficulty

Moderate

Steps

11

Time Required

                          1 - 2 hours

Sections

3

  • Bottom Cover
  • 3 steps
  • LCD Assembly
  • 6 steps
  • LCD Bezel
  • 2 steps

Flags

0

  • BackLenovo ThinkPad T480s

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The screen bezel is a plastic border that covers the internal components within the screen assembly including the WLAN and WWAN antennas and camera. You may need to replace your screen bezel if it is cracked or damaged. Be sure to clean any remaining adhesive on the display assembly and reapply fresh adhesive when installing a new display bezel for best results.

Make sure to disable the internal battery, power down your device, and disconnect from any external power sources before you begin.

What you need

Step 1

              Bottom Cover
  • Disable the battery, power down the device, and unplug the power adapter from your device before proceeding/beginning the guide.
  • Loosen the six captive screws with a Phillips #1 screwdriver.

Disable the battery, power down the device, and unplug the power adapter from your device before proceeding/beginning the guide.

Loosen the six captive screws with a Phillips #1 screwdriver.

1024

Step 2

  • Remove the bottom cover with an opening tool.
  • Start from the top edge near the hinge and work your way along the edge until all of the clips are unsnapped.

Remove the bottom cover with an opening tool.

Start from the top edge near the hinge and work your way along the edge until all of the clips are unsnapped.

Step 3

  • Lift the bottom cover off.

Lift the bottom cover off.

Step 4

              LCD Assembly
  • Use the spudger to disconnect the coaxial cables from the Wi-Fi card and WWAN card.
  • When reassembling the Wi-Fi card, reattach the black wire closest to the screw and the gray wire on the other side of the black wire. With the WWAN card, reattach the blue wire on the left and the orange wire on the right.
  • There are also small color coded arrows on each card that match the corresponding wires, to make sure you connect to the correct spot.

Use the spudger to disconnect the coaxial cables from the Wi-Fi card and WWAN card.

When reassembling the Wi-Fi card, reattach the black wire closest to the screw and the gray wire on the other side of the black wire. With the WWAN card, reattach the blue wire on the left and the orange wire on the right.

There are also small color coded arrows on each card that match the corresponding wires, to make sure you connect to the correct spot.

Step 5

  • Use the spudger to disconnect the LCD cable from the motherboard.

Use the spudger to disconnect the LCD cable from the motherboard.

Step 6

  • Disconnect the camera cable from the motherboard using a spudger.

Disconnect the camera cable from the motherboard using a spudger.

Step 7

  • Remove all antenna cables from their routing.

Remove all antenna cables from their routing.

Step 8

  • Using the Phillips #1 screwdriver, remove three 5 mm screws from the left hinge and three 5 mm screws from the right hinge.

Using the Phillips #1 screwdriver, remove three 5 mm screws from the left hinge and three 5 mm screws from the right hinge.

Step 9

  • Carefully rotate the hinges upward and remove the bottom of the machine from the LCD unit.

Carefully rotate the hinges upward and remove the bottom of the machine from the LCD unit.

Step 10

              LCD Bezel
  • Using the spudger, pry the LCD bezel up from the edges starting near the hinges.
  • It is attached by adhesive so be careful not to break it. You may hear loud snaps when detaching the clips; this is normal.

Using the spudger, pry the LCD bezel up from the edges starting near the hinges.

It is attached by adhesive so be careful not to break it. You may hear loud snaps when detaching the clips; this is normal.

Step 11

  • Use the spudger to remove the internal bezel.
  • Start at the corner by the hinge and lift the edge of the internal bezel up with the pointed end of the spudger.
  • Hold the internal bezel with your fingers and work your way around the perimeter of the screen carefully pulling the bezel up.
  • You will feel resistance and hear snapping as you remove the bezel because it is connected with clips. Be careful that you don’t crack the bezel. The plastic is delicate in places.

Use the spudger to remove the internal bezel.

Start at the corner by the hinge and lift the edge of the internal bezel up with the pointed end of the spudger.

Hold the internal bezel with your fingers and work your way around the perimeter of the screen carefully pulling the bezel up.

You will feel resistance and hear snapping as you remove the bezel because it is connected with clips. Be careful that you don’t crack the bezel. The plastic is delicate in places.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Sarah Westberg

Member since: 03/11/2019

16,818 Reputation

                                      65 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored