Difficulty
Easy
Steps
14
Time Required
15 - 20 minutes
Sections
3
- External Battery
- 2 steps
- Bottom Cover
- 6 steps
- USB Board Cable
- 6 steps
Flags
0
BackLenovo ThinkPad T460
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The USB board cable connects the USB port to the motherboard. If your laptop does not recognize any peripherals plugged into the USB port, the USB board cable may be loose or faulty.
Make sure to disable the internal battery, power down your device, and disconnect from any external power sources before you begin.
What you need
Step 1
External Battery
- Before you begin this guide, make sure to disable the internal battery, power down your device, and disconnect from any external power sources.
- Place the laptop so that the bottom is facing upwards.
- Slide the latch on the left side of the battery to the left until it clicks in place.
Before you begin this guide, make sure to disable the internal battery, power down your device, and disconnect from any external power sources.
Place the laptop so that the bottom is facing upwards.
Slide the latch on the left side of the battery to the left until it clicks in place.
1024
Step 2
- Slide the latch on the right side of the battery to the right and hold it in place with your thumb.
- Use your other hand to slide the battery towards the back of the laptop.
- Lift the battery up and away from the laptop.
Slide the latch on the right side of the battery to the right and hold it in place with your thumb.
Use your other hand to slide the battery towards the back of the laptop.
Lift the battery up and away from the laptop.
Step 3
Bottom Cover
- Loosen the eight captive screws in the bottom cover using a Phillips #1 screwdriver.
Loosen the eight captive screws in the bottom cover using a Phillips #1 screwdriver.
Step 4
- Insert the flat end of a spudger in between the bottom cover and the rest of the laptop, starting in the lower left corner.
- Pry the lower left corner of the bottom cover up by a few millimeters.
- Slide the spudger along the bottom of the laptop to release the clips until you reach the lower right corner.
- You may hear some snapping noises as the clips are released.
Insert the flat end of a spudger in between the bottom cover and the rest of the laptop, starting in the lower left corner.
Pry the lower left corner of the bottom cover up by a few millimeters.
Slide the spudger along the bottom of the laptop to release the clips until you reach the lower right corner.
You may hear some snapping noises as the clips are released.
Step 5
- Slide the spudger along the right and top sides of the bottom cover to release the clips.
- You may hear some snapping noises as the clips are released.
- Potential for device damage: If the clips do not release easily, check to ensure that the captive screws are fully loosened. Forcing the clips to detach can crack the bottom cover.
Slide the spudger along the right and top sides of the bottom cover to release the clips.
Potential for device damage: If the clips do not release easily, check to ensure that the captive screws are fully loosened. Forcing the clips to detach can crack the bottom cover.
Step 6
- Use the spudger to pry the upper left corner up by a few millimeters.
- Pry up the sections of the bottom cover with printed logos of the ports.
- Potential for device damage: Prying inside the ports themselves can damage your laptop. Be sure to only pry up on the sections of the cover that extend past the ports.
Use the spudger to pry the upper left corner up by a few millimeters.
Pry up the sections of the bottom cover with printed logos of the ports.
Potential for device damage: Prying inside the ports themselves can damage your laptop. Be sure to only pry up on the sections of the cover that extend past the ports.
Step 7
- Use the spudger to pry up the bottom cover in the lower portion of the external battery compartment by a few millimeters.
Use the spudger to pry up the bottom cover in the lower portion of the external battery compartment by a few millimeters.
Step 8
- Use both hands to lift the bottom cover up and away from the laptop.
Use both hands to lift the bottom cover up and away from the laptop.
Step 9
USB Board Cable
- Use your fingers to lift the gray wire out its slot.
Use your fingers to lift the gray wire out its slot.
Step 10
- Use your fingers to lift the black wire out of its slot.
Use your fingers to lift the black wire out of its slot.
Step 11
- Use a pair of blunt nose tweezers to pull the white fan connector out of its socket on the motherboard.
- This connector may be difficult to remove. You can use a pair of tweezers to gently rock the connector back and forth until it is free from the socket.
Use a pair of blunt nose tweezers to pull the white fan connector out of its socket on the motherboard.
This connector may be difficult to remove. You can use a pair of tweezers to gently rock the connector back and forth until it is free from the socket.
Step 12
- Use the flat end of a spudger to detach the USB cable from the USB board.
Use the flat end of a spudger to detach the USB cable from the USB board.
Step 13
- Use the flat end of a spudger to detach the USB cable from the motherboard.
Use the flat end of a spudger to detach the USB cable from the motherboard.
Step 14
- Use your fingers to lift the USB board cable up and away from the laptop.
Use your fingers to lift the USB board cable up and away from the laptop.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.
Cancel: I did not complete this guide.
Author
Kristen Gismondi
Member since: 11/12/2014
69,397 Reputation
176 Guides authored
Badges:
44
+41 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored
