Lenovo Thinkpad T460 Bottom Cover Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

External Battery
2 steps
Bottom Cover
6 steps

Flags

BackLenovo ThinkPad T460
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The bottom cover encases the internal components of the laptop and provides proper ventilation for the fan. You may need to replace the bottom cover if it is cracked or physically damaged to the point where it is exposing the laptop’s internals.

Make sure to disable the internal battery, power down your device, and disconnect from any external power sources before you begin.

What you need

Step 1

              External Battery

Before you begin this guide, make sure to disable the internal battery, power down your device, and disconnect from any external power sources.
Place the laptop so that the bottom is facing upwards.
Slide the latch on the left side of the battery to the left until it clicks in place.

Before you begin this guide, make sure to disable the internal battery, power down your device, and disconnect from any external power sources.

Place the laptop so that the bottom is facing upwards.

Slide the latch on the left side of the battery to the left until it clicks in place.

1024

Step 2

Slide the latch on the right side of the battery to the right and hold it in place with your thumb.
Use your other hand to slide the battery towards the back of the laptop.
Lift the battery up and away from the laptop.

Slide the latch on the right side of the battery to the right and hold it in place with your thumb.

Use your other hand to slide the battery towards the back of the laptop.

Lift the battery up and away from the laptop.

Step 3

              Bottom Cover

Loosen the eight captive screws in the bottom cover using a Phillips #1 screwdriver.

Loosen the eight captive screws in the bottom cover using a Phillips #1 screwdriver.

Step 4

Insert the flat end of a spudger in between the bottom cover and the rest of the laptop, starting in the lower left corner.
Pry the lower left corner of the bottom cover up by a few millimeters.
Slide the spudger along the bottom of the laptop to release the clips until you reach the lower right corner.
You may hear some snapping noises as the clips are released.

Insert the flat end of a spudger in between the bottom cover and the rest of the laptop, starting in the lower left corner.

Pry the lower left corner of the bottom cover up by a few millimeters.

Slide the spudger along the bottom of the laptop to release the clips until you reach the lower right corner.

You may hear some snapping noises as the clips are released.

Step 5

Slide the spudger along the right and top sides of the bottom cover to release the clips.
You may hear some snapping noises as the clips are released.
Potential for device damage: If the clips do not release easily, check to ensure that the captive screws are fully loosened. Forcing the clips to detach can crack the bottom cover.

Slide the spudger along the right and top sides of the bottom cover to release the clips.

Potential for device damage: If the clips do not release easily, check to ensure that the captive screws are fully loosened. Forcing the clips to detach can crack the bottom cover.

Step 6

Use the spudger to pry the upper left corner up by a few millimeters.
Pry up the sections of the bottom cover with printed logos of the ports.
Potential for device damage: Prying inside the ports themselves can damage your laptop. Be sure to only pry up on the sections of the cover that extend past the ports.

Use the spudger to pry the upper left corner up by a few millimeters.

Pry up the sections of the bottom cover with printed logos of the ports.

Potential for device damage: Prying inside the ports themselves can damage your laptop. Be sure to only pry up on the sections of the cover that extend past the ports.

Step 7

Use the spudger to pry up the bottom cover in the lower portion of the external battery compartment by a few millimeters.

Use the spudger to pry up the bottom cover in the lower portion of the external battery compartment by a few millimeters.

Step 8

Use both hands to lift the bottom cover up and away from the laptop.

Use both hands to lift the bottom cover up and away from the laptop.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Kristen Gismondi

Member since: 11/12/2014

69,397 Reputation

                                      176 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team