Difficulty

Moderate

Steps

11

Time Required

                          10 - 20 minutes

Sections

5

  • External Battery
  • 1 step
  • Back Cover
  • 2 steps
  • RAM
  • 2 steps
  • Fan and Heatsink Assembly
  • 3 steps
  • Daughterboard
  • 3 steps

Flags

0

  • BackLenovo Thinkpad T450

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

As for the Lenovo ThinkPad T450 laptop, the daughterboard houses the USB port on the upper left side of the laptop. If you find that the devices you plug into this USB port are not being recognized, it may be time to replace the daughterboard. Follow these simple instructions to replace the daughterboard in your device.

What you need

Step 1

              External Battery
  • Using your hands, slide the two locking tabs away from each other to release the battery.
  • Slide the battery up and out of the device.

Using your hands, slide the two locking tabs away from each other to release the battery.

Slide the battery up and out of the device.

1024

Step 2

              Back Cover
  • Using the JIS #00 screwdriver, unscrew seven screws from the back cover.
  • These screws are not removable and will remain in the back cover.
  • Use the JIS #00 screwdriver to remove the single 2.8 mm screw from the back cover.

Using the JIS #00 screwdriver, unscrew seven screws from the back cover.

These screws are not removable and will remain in the back cover.

Use the JIS #00 screwdriver to remove the single 2.8 mm screw from the back cover.

Step 3

  • Insert a plastic opening tool into the edges of the laptop and work your way around the edges to pry off the back cover from the device.
  • Remove the back cover from the device.

Insert a plastic opening tool into the edges of the laptop and work your way around the edges to pry off the back cover from the device.

Remove the back cover from the device.

Step 4

              RAM
  • Lift up the black piece of tape and remove it to uncover the RAM sticks underneath.

Lift up the black piece of tape and remove it to uncover the RAM sticks underneath.

Step 5

  • Using your fingers, push the two clips securing the RAM away from each other to release the RAM.
  • The RAM stick should pop up at a 30 degree angle.
  • Remove the RAM stick from the device.
  • Repeat this step for any additional RAM sticks.

Using your fingers, push the two clips securing the RAM away from each other to release the RAM.

The RAM stick should pop up at a 30 degree angle.

Remove the RAM stick from the device.

Repeat this step for any additional RAM sticks.

Step 6

              Fan and Heatsink Assembly
  • Using the JIS #00 screwdriver, unscrew the four screws securing the fan and heatsink assembly to the motherboard.
  • These screws are not removable and will stay on the fan and heatsink assembly.

Using the JIS #00 screwdriver, unscrew the four screws securing the fan and heatsink assembly to the motherboard.

These screws are not removable and will stay on the fan and heatsink assembly.

Step 7

  • Disconnect the fan and heatsink assembly from the motherboard using the plastic opening tool.

Disconnect the fan and heatsink assembly from the motherboard using the plastic opening tool.

Step 8

  • Lift up the fan and heatsink assembly and remove it from the device.
  • When you reassemble your device, don’t forget to reapply thermal paste to the back of the heatsink and fan assembly. For proper technique and thermal paste application, please visit the How to Apply Thermal Paste guide.

Lift up the fan and heatsink assembly and remove it from the device.

When you reassemble your device, don’t forget to reapply thermal paste to the back of the heatsink and fan assembly. For proper technique and thermal paste application, please visit the How to Apply Thermal Paste guide.

Step 9

              Daughterboard
  • Use the plastic opening tool to disconnect the daughterboard cable from the motherboard.

Use the plastic opening tool to disconnect the daughterboard cable from the motherboard.

Step 10

  • Using the JIS #00 screwdriver, remove the two 2.8 mm screws securing the daughterboard to the device.

Using the JIS #00 screwdriver, remove the two 2.8 mm screws securing the daughterboard to the device.

Step 11

  • Lift up and remove the daughterboard from the device.

Lift up and remove the daughterboard from the device.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Cancel: I did not complete this guide.

Author

                    Justin Ogihara

Member since: 09/18/2017

23,793 Reputation

                                      52 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       EDU Team                        

                                                  Member of EDU Team 



                    Community                     


                                            7 Members                     


                                            487 Guides authored