Lenovo Thinkpad T430S Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          2 hours

Sections

Battery
1 step
RAM Stick
2 steps
Hard Drive
2 steps
Motherboard
11 steps

Flags

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

BackLenovo ThinkPad T430s
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The motherboard connects the components of the ThinkPad and allows them to communicate. If the motherboard breaks, it can cause your ThinkPad to shut off suddenly, fail to boot, or display the blue screen of death.

If you experience these symptoms, click this link to access the troubleshooting guide for the ThinkPad T430s. This will help you determine if the motherboard is at fault.

What you need

Step 1

              Battery

Flip your ThinkPad on its back.
In the bottom left corner of your ThinkPad, slide the lever to the left. Hold the lever there.
Use your other hand to lift the battery up by prying the notch to the left of the lever.
Tilt the battery up and remove it from the ThinkPad.

Flip your ThinkPad on its back.

In the bottom left corner of your ThinkPad, slide the lever to the left. Hold the lever there.

Use your other hand to lift the battery up by prying the notch to the left of the lever.

Tilt the battery up and remove it from the ThinkPad.

1024

Step 2

              RAM Stick

With the Phillips #0 screwdriver, loosen the two 30 mm screws holding down the RAM stick plate.
Pry up the plate and set it aside.

With the Phillips #0 screwdriver, loosen the two 30 mm screws holding down the RAM stick plate.

Pry up the plate and set it aside.

Step 3

Use the pointy end of the spudger to bend the bars holding the RAM stick in place.
Lift the RAM stick up and out of the stick holder.

Use the pointy end of the spudger to bend the bars holding the RAM stick in place.

Lift the RAM stick up and out of the stick holder.

Step 4

              Hard Drive

Unscrew the 40 mm screw with the Phillips head #1 screwdriver.

Unscrew the 40 mm screw with the Phillips head #1 screwdriver.

Step 5

Pull the hard drive out with the black ribbon attached to it.

Pull the hard drive out with the black ribbon attached to it.

Step 6

              Motherboard

Flip your ThinkPad over so the back faces up.
With the Phillips #0 screwdriver, remove the seven 50 mm screws on the outer edge of the case.
Remove the two 70 mm screws in the upper corners of the case.
Remove the five 50 mm screws in the battery compartment.

Flip your ThinkPad over so the back faces up.

With the Phillips #0 screwdriver, remove the seven 50 mm screws on the outer edge of the case.

Remove the two 70 mm screws in the upper corners of the case.

Remove the five 50 mm screws in the battery compartment.

Step 7

In the RAM compartment, pry the black, white, and grey wires up from the Wi-Fi card with the pointy end of the spudger.
Remove the 30 mm screw holding down the Wi-Fi card with the Phillips #0 screwdriver.
Pull out the Wi-Fi card.
Remove the 60 mm and 30 mm screws in the RAM stick compartment.

In the RAM compartment, pry the black, white, and grey wires up from the Wi-Fi card with the pointy end of the spudger.

Remove the 30 mm screw holding down the Wi-Fi card with the Phillips #0 screwdriver.

Pull out the Wi-Fi card.

Remove the 60 mm and 30 mm screws in the RAM stick compartment.

Step 8

Remove the 50 mm and 30 mm screws in the hard drive compartment.

Remove the 50 mm and 30 mm screws in the hard drive compartment.

Step 9

Flip the ThinkPad right side up and open the lid.
Wedge the flat end of the spudger between the keyboard and the palm rest. Push the keyboard away from you until it pops out.
Lift the keyboard from the palm rest to expose the ribbon connecting the keyboard to the motherboard.
Pry the keyboard ribbon up from the motherboard with the flat end of the spudger.
Set the keyboard aside.

Flip the ThinkPad right side up and open the lid.

Wedge the flat end of the spudger between the keyboard and the palm rest. Push the keyboard away from you until it pops out.

Lift the keyboard from the palm rest to expose the ribbon connecting the keyboard to the motherboard.

Pry the keyboard ribbon up from the motherboard with the flat end of the spudger.

Set the keyboard aside.

Step 10

Remove the two 50 mm screws from the case covering the disk drive.
Thread the wires that come from the RAM compartment up through the hole in the motherboard. Unwind them from the computer case.
Wedge the flat end of the spudger in between the palm rest and the bottom case. Unsnap the edges of the palm rest and case until they disconnect.
Lift the palm rest up from the motherboard.

Remove the two 50 mm screws from the case covering the disk drive.

Thread the wires that come from the RAM compartment up through the hole in the motherboard. Unwind them from the computer case.

Wedge the flat end of the spudger in between the palm rest and the bottom case. Unsnap the edges of the palm rest and case until they disconnect.

Lift the palm rest up from the motherboard.

Step 11

Pull the red, blue, and white wires in the left corner away from the motherboard.
Peel the snap securing the ribbon with the pointy end of the spudger.
Pull the ribbon back towards you.

Pull the red, blue, and white wires in the left corner away from the motherboard.

Peel the snap securing the ribbon with the pointy end of the spudger.

Pull the ribbon back towards you.

Step 12

Rotate the ThinkPad so the back side faces you.
With the Phillips #1 screwdriver, unscrew the two 70 mm screws from the corners.
Lift the screen and pull it out of the hinges. Set the screen down behind the rest of the ThinkPad.

Rotate the ThinkPad so the back side faces you.

With the Phillips #1 screwdriver, unscrew the two 70 mm screws from the corners.

Lift the screen and pull it out of the hinges. Set the screen down behind the rest of the ThinkPad.

Step 13

With the pointy end of the spudger, lift the plastic snap holding down the SN4 LVDS cable. Pull the cable out of the clasp towards you.
Pry the SN4 LED cable out of where it connects to the motherboard.
Set the display aside.

With the pointy end of the spudger, lift the plastic snap holding down the SN4 LVDS cable. Pull the cable out of the clasp towards you.

Pry the SN4 LED cable out of where it connects to the motherboard.

Set the display aside.

Step 14

With the pointy end of the spudger, lift the plastic snap securing the ribbon at the front of the ThinkPad.
Pull the ribbon out of the clasp towards you.

With the pointy end of the spudger, lift the plastic snap securing the ribbon at the front of the ThinkPad.

Pull the ribbon out of the clasp towards you.

Step 15

Unscrew the 90 mm screw, five 50 mm screws, and four 30 mm screws on the motherboard using a Phillips #0 screwdriver.
When you remove the screws, the small motherboard stick in the top right corner will pop out of the case. Pull it out.
Lift the motherboard out of the case.

Unscrew the 90 mm screw, five 50 mm screws, and four 30 mm screws on the motherboard using a Phillips #0 screwdriver.

When you remove the screws, the small motherboard stick in the top right corner will pop out of the case. Pull it out.

Lift the motherboard out of the case.

Step 16

Flip the motherboard over so the back faces up.
Loosen the four screws securing the heat sink to the motherboard. The silver metal rectangle on the front of the motherboard will fall off. Set it aside.
Lift the fan and heat sink away from the motherboard.

Flip the motherboard over so the back faces up.

Loosen the four screws securing the heat sink to the motherboard. The silver metal rectangle on the front of the motherboard will fall off. Set it aside.

Lift the fan and heat sink away from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Melissa Rogers

Member since: 09/02/2020

651 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Western Carolina University, Team S1-G1, Virtue Fall 2020                        

                                                  Member of Western Carolina University, Team S1-G1, Virtue Fall 2020 



                    WCU-VIRTUE-F20S1G1                     


                                            1 Member                     


                                            5 Guides authored

Inconsistent Images#

Introduction#

What you need#

Team#

Inconsistent Images

Introduction

What you need

Team