Difficulty
Easy
Steps
5
Time Required
5 minutes
Sections
1
- Hard Drive
- 5 steps
Flags
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackLenovo ThinkPad Edge E420s
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The hard drive is a piece of hardware that stores and retrieves data in your computer. A failing hard drive can cause your laptop to produce irregular noises and/or continuous crashes and error messages like “file not found” or “Windows detected a hard disk problem.” In some cases, your computer may not boot at all if it experiences hard drive failure.
Before using this guide, make sure to review the troubleshooting page—oftentimes, malware or corrupted files can be fixed without replacing the hard drive.
If you’re running low on storage, you may want to consider upgrading your hard drive. Follow instructions here to see how much storage space you have left. This device supports HDDs in capacities of 250GB and 320GB (hard drive specs are: SATA 3.0Gb/s, 2.5" wide, 7mm high). It can also support SSDs with the following specs: SATA 3.0Gb/s 128GB SSD, 2.5" wide, 7mm high.
Be sure to back up your hard drive before replacing it so you don’t lose any data while you’re doing the replacement. Make sure to power off your laptop completely and disconnect from any external power source prior to beginning the process.
What you need
Step 1
Hard Drive
- There is no external access to the battery. Please make sure the at the battery has been drained or disabled through BIOS before beginning.
- Flip the device over.
There is no external access to the battery. Please make sure the at the battery has been drained or disabled through BIOS before beginning.
Flip the device over.
1024
Step 2
- Use a Phillips #00 screwdriver to remove one M2 x 3mm screw from the side of the device.
Use a Phillips #00 screwdriver to remove one M2 x 3mm screw from the side of the device.
Step 3
- Swing the cover out slightly like a hinge.
- Pull the cover directly away from the case towards the base of the laptop.
- Lift the cover up and away from the device to remove it.
- You may hear a slight pop when you pull the cover off.
Swing the cover out slightly like a hinge.
Pull the cover directly away from the case towards the base of the laptop.
Lift the cover up and away from the device to remove it.
You may hear a slight pop when you pull the cover off.
Step 4
- Use the clear tab to slide the hard drive out of the device.
Use the clear tab to slide the hard drive out of the device.
Step 5
- To replace the hard drive, remove the four M2 × 4mm wafer-headed screws on the sides of the hard drive case using a Phillips #00 screwdriver.
- Slide the old hard drive directly out.
- When reassembling, make sure the hard drive is securely in the case before beginning.
To replace the hard drive, remove the four M2 × 4mm wafer-headed screws on the sides of the hard drive case using a Phillips #00 screwdriver.
Slide the old hard drive directly out.
When reassembling, make sure the hard drive is securely in the case before beginning.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 4 other contributors
Keyadri Summerlin
Member since: 10/02/2018
1,003 Reputation
7 Guides authored
Badges:
12
+9 more badges
Team
Linn Benton Community College, Team S2-G1, Karnes Fall 2018
Member of Linn Benton Community College, Team S2-G1, Karnes Fall 2018
LBCC-KARNES-F18S2G1
3 Members
8 Guides authored
