Lenovo Tab S8 Speakers Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Battery
3 steps
Motherboard
4 steps
Speakers
1 step

Flags

BackLenovo Tab S8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure the device is powered off.
Gently insert a spudger into one of the bottom corners between the screen and body case.
Slide the spudger along the inside of the crack in order to pry the case open.
Be careful of the small volume and power buttons when prying the case with the spudger. They are connected with small pieces of plastic that break easily.

Make sure the device is powered off.

Gently insert a spudger into one of the bottom corners between the screen and body case.

Slide the spudger along the inside of the crack in order to pry the case open.

Be careful of the small volume and power buttons when prying the case with the spudger. They are connected with small pieces of plastic that break easily.

1024

Step 2

After removing the cover, remove the M1.6 x 2 mm screw from the battery cable with the JIS J000 screwdriver.
Using screwdriver bits that do not fit in the screw head might strip the screw and render it unusable.
Remove the tape by gently scraping the edges up with the spudger.

After removing the cover, remove the M1.6 x 2 mm screw from the battery cable with the JIS J000 screwdriver.

Using screwdriver bits that do not fit in the screw head might strip the screw and render it unusable.

Remove the tape by gently scraping the edges up with the spudger.

Step 3

Before removing the battery, be sure to disconnect the ribbon cables underneath it. The cables might stick to the battery during removal and cause damage.
Gently lift the flaps on the four ZIF connectors to disconnect the cables.
Use the plastic card to gently pry the battery from the device.
There may be glue holding the battery to the device. Use the spudger to detach any glue while the battery is partially raised by the card.

Before removing the battery, be sure to disconnect the ribbon cables underneath it. The cables might stick to the battery during removal and cause damage.

Gently lift the flaps on the four ZIF connectors to disconnect the cables.

Use the plastic card to gently pry the battery from the device.

There may be glue holding the battery to the device. Use the spudger to detach any glue while the battery is partially raised by the card.

Step 4

              Motherboard

Use the tip of a spudger or your fingernail to flip up the small locking flap. Then, you can safely pull the cable out from under the camera.

Use the tip of a spudger or your fingernail to flip up the small locking flap. Then, you can safely pull the cable out from under the camera.

Step 5

Remove the press-fit cable located next to the camera by using opening tool to gently pry it up.
Unlock the ZIF connector by lifting the black bar and sliding the ribbon cable out.

Remove the press-fit cable located next to the camera by using opening tool to gently pry it up.

Unlock the ZIF connector by lifting the black bar and sliding the ribbon cable out.

Step 6

Remove the five M1.6 x 2 mm screws from the motherboard with the JIS J000 screwdriver.
There is one screw hidden under a circular white sticker directly below the camera. Remove the sticker to take out the screw that is underneath it.
Cut or remove the piece of silver tape from the motherboard.

Remove the five M1.6 x 2 mm screws from the motherboard with the JIS J000 screwdriver.

There is one screw hidden under a circular white sticker directly below the camera. Remove the sticker to take out the screw that is underneath it.

Cut or remove the piece of silver tape from the motherboard.

Step 7

Use the spudger to gently pry the motherboard out of the frame from each side.

Use the spudger to gently pry the motherboard out of the frame from each side.

Step 8

              Speakers

Once you have removed the motherboard and the battery, locate both the upper and lower speakers.
The lower speaker wire is glued to the back casing of the device, so be gentle when removing the wire.
Lift up the wire with a plastic opening tool. Make sure this tool has a sharp edge.

Once you have removed the motherboard and the battery, locate both the upper and lower speakers.

The lower speaker wire is glued to the back casing of the device, so be gentle when removing the wire.

Lift up the wire with a plastic opening tool. Make sure this tool has a sharp edge.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Thomas Rill

Member since: 08/26/2015

338 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team 3-6, Eyestone Fall 2015                        

                                                  Member of USF Tampa, Team 3-6, Eyestone Fall 2015 



                    USFT-EYESTONE-F15S3G6                     


                                            3 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team