Difficulty

Moderate

Steps

10

Time Required

                          10 minutes

Sections

2

  • Battery
  • 3 steps
  • Keyboard
  • 7 steps

Flags

0

  • BackLenovo S20-30

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Flip the Lenovo S20-30 over so that the bottom panel is facing upward.

Flip the Lenovo S20-30 over so that the bottom panel is facing upward.

1024

Step 2

  • Slide the manual battery latch to the unlock position, so that the red is showing.

Slide the manual battery latch to the unlock position, so that the red is showing.

Step 3

  • Slide and hold the spring-loaded battery latch on the other side (right) while sliding the battery out of the computer.
  • Grab new Lenovo S20-30 battery for replacement.

Slide and hold the spring-loaded battery latch on the other side (right) while sliding the battery out of the computer.

Grab new Lenovo S20-30 battery for replacement.

Step 4

              Keyboard
  • Remove the two front rubber feet using a long metal spudger.
  • Use your Phillips #0 screwdriver to remove the two M2.5 x 5mm flat-head screws located underneath the pads.

Remove the two front rubber feet using a long metal spudger.

Use your Phillips #0 screwdriver to remove the two M2.5 x 5mm flat-head screws located underneath the pads.

Step 5

  • Use the Phillips #0 screwdriver to remove the nine M2 x 4mm flat head screws located on the outer edges on the back of the laptop.
  • Make sure to keep these screws separated from future screws that will be disassembled throughout this process.

Use the Phillips #0 screwdriver to remove the nine M2 x 4mm flat head screws located on the outer edges on the back of the laptop.

Make sure to keep these screws separated from future screws that will be disassembled throughout this process.

Step 6

  • Use the long metal spudger to pry open the bottom half of the laptop.
  • Gently lift the cover off to reveal the motherboard.

Use the long metal spudger to pry open the bottom half of the laptop.

Gently lift the cover off to reveal the motherboard.

Step 7

  • Remove the four M2 x 3mm flat-head screw using a Phillips #000 screwdriver.

Remove the four M2 x 3mm flat-head screw using a Phillips #000 screwdriver.

Step 8

  • Flip over laptop and open the lid to have access to the keyboard.
  • Use a plastic opening tool to pry apart the keyboard.

Flip over laptop and open the lid to have access to the keyboard.

Use a plastic opening tool to pry apart the keyboard.

Step 9

  • A connector is attached to the keyboard.
  • Remove it by gently pulling it outward.

A connector is attached to the keyboard.

Remove it by gently pulling it outward.

Step 10

  • Grab replacement keyboard to insert back into place.

Grab replacement keyboard to insert back into place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    ILEANISSE SOTO

Member since: 10/01/2018

187 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       McKendree University, Team S1-G4, Quinn Fall 2018                        

                                                  Member of McKendree University, Team S1-G4, Quinn Fall 2018 



                    MCKU-QUINN-F18S1G4                     


                                            2 Members                     


                                            3 Guides authored

ed paz - Oct 12, 2019

Reply

where can i find a replacement keyboard/ or what model # do i need?