Difficulty
Moderate
Steps
18
Time Required
45 minutes - 1 hour
Sections
4
- Back Cover
- 10 steps
- Battery Disconnect
- 2 steps
- Right SSD Replacement
- 4 steps
- Battery
- 2 steps
Flags
1
Provided Hardware
A manufacturer provided iFixit with this device or component.
BackLenovo Legion 5 Pro 16ACH6H
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
For your safety, discharge the battery below 25% before disassembling your device. This reduces the risk of fire if the battery is accidentally damaged during the repair. If your battery is swollen, take appropriate precautions.
What you need
Step 1
Back cover removal
- Use a Phillips screwdriver to remove the following ten screws securing the back cover to frame:
- Six 12.7 mm PH00 screws
- Four 4.2 mm PH00 screws
Use a Phillips screwdriver to remove the following ten screws securing the back cover to frame:
Six 12.7 mm PH00 screws
Four 4.2 mm PH00 screws
1024
Step 2
Release the front clips
- Insert the rounded edge of an opening pick between the back cover and the frame in the lower right corner.
Insert the rounded edge of an opening pick between the back cover and the frame in the lower right corner.
Step 3
- Angle the pick to about 45˚.
- Slide the pick along the front edge to release the clips securing the back cover to the frame.
Angle the pick to about 45˚.
Slide the pick along the front edge to release the clips securing the back cover to the frame.
Step 4
Release the right clips
- Insert the rounded edge of an opening pick between the back cover and the frame on the right edge.
- Angle the pick to about 30˚ and slide down the right edge until you reach the plastic vents on the side.
Insert the rounded edge of an opening pick between the back cover and the frame on the right edge.
Angle the pick to about 30˚ and slide down the right edge until you reach the plastic vents on the side.
Step 5
Release the left clips
- Repeat the same procedure on the left edge to release the clips.
Repeat the same procedure on the left edge to release the clips.
Step 6
Release the right vent clips
- Position the laptop vertically so you can easily access the plastic vents.
- Slide the rounded edge of an opening pick between the frame and the plastic vents on the right side near the USB-A port.
- Rotate the pick so that it is positioned on top of the plastic vents.
Position the laptop vertically so you can easily access the plastic vents.
Slide the rounded edge of an opening pick between the frame and the plastic vents on the right side near the USB-A port.
Rotate the pick so that it is positioned on top of the plastic vents.
Step 7
- Push the pick between the frame and plastic vents.
- Slide the pick along the top edge of the plastic vents to release the clips.
Push the pick between the frame and plastic vents.
Slide the pick along the top edge of the plastic vents to release the clips.
Step 8
Release the left vent clips
- Slide the rounded edge of an opening pick between the frame and the plastic vents on the left side near the USB-C port.
- Rotate the pick so that it is positioned on top of the plastic vents.
Slide the rounded edge of an opening pick between the frame and the plastic vents on the left side near the USB-C port.
Step 9
Step 10
Remove the back cover
- Lift the back cover up and remove it from the chassis.
- During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.
Lift the back cover up and remove it from the chassis.
During reassembly, this is a good point to power on your laptop and test all functions before sealing it up. Be sure to power your laptop back down before you continue working.
Step 11
Disconnect the battery
- Use the pointed end of a spudger to push each side of the battery connector to loosen it.
Use the pointed end of a spudger to push each side of the battery connector to loosen it.
Step 12
- Use the flat end of a spudger to push out and disconnect battery cable.
Use the flat end of a spudger to push out and disconnect battery cable.
Step 13
Right SSD removal
- Use a Phillips screwdriver to remove the three 5.1 mm PH00 screws securing the right SSD shield to the motherboard.
- During reassembly, make sure the hole on the top of the shield aligns with the post on the chassis.
Use a Phillips screwdriver to remove the three 5.1 mm PH00 screws securing the right SSD shield to the motherboard.
During reassembly, make sure the hole on the top of the shield aligns with the post on the chassis.
Step 14
Remove the SSD shield
- Grab the SSD shield and lift up to remove it.
Grab the SSD shield and lift up to remove it.
Step 15
- Use a Phillips screwdriver to remove the 2.6 mm PH1 screw securing the SSD to the motherboard.
- The SSD will spring up to about 30˚ when the screw is removed.
Use a Phillips screwdriver to remove the 2.6 mm PH1 screw securing the SSD to the motherboard.
The SSD will spring up to about 30˚ when the screw is removed.
Step 16
Remove the right SSD
- Grip the edges of the SSD near the screw indent.
- Gently pull to remove the SSD.
Grip the edges of the SSD near the screw indent.
Gently pull to remove the SSD.
Step 17
Unfasten the battery
- Use your Phillips screwdriver to remove the six 5.1 mm-long screws securing the battery.
Use your Phillips screwdriver to remove the six 5.1 mm-long screws securing the battery.
Step 18
Remove the battery
- Remove the battery from its recess.
Remove the battery from its recess.
To reassemble your device, follow these instructions in reverse order.
For optimal performance, calibrate your newly installed battery after completing this guide.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Lenovo Legion answers community for help.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Clay Eickemeyer
Member since: 09/19/2022
14,946 Reputation
125 Guides authored
Badges:
27
+24 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored
