Difficulty
Moderate
Steps
12
Time Required
40 minutes
Sections
1
- Front Camera
- 12 steps
Flags
0
BackLenovo IdeaTab S6000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Camera
- Remove the speaker screens by working them loose with a plastic opening tool. You may need to first loosen them with tweezers or a spudger.
- These screens are held in place by glue that is hard to remove. Please take your time to ensure that that this step is done correctly.
Remove the speaker screens by working them loose with a plastic opening tool. You may need to first loosen them with tweezers or a spudger.
These screens are held in place by glue that is hard to remove. Please take your time to ensure that that this step is done correctly.
1024
Step 2
- Remove the screws from both of the spots that were covered with a Phillips #000 screwdriver.
Remove the screws from both of the spots that were covered with a Phillips #000 screwdriver.
Step 3
- Go all around the casing, prying the screen away from the backing with the spudger.
- It will make a popping sound each time one of the lock tabs is disconnected.
- Take your time as you move all around the device when prying the backing off.
- Do not use a metal tool for this.
Go all around the casing, prying the screen away from the backing with the spudger.
It will make a popping sound each time one of the lock tabs is disconnected.
Take your time as you move all around the device when prying the backing off.
Do not use a metal tool for this.
Step 4
- Using either the plastic opening tool or your fingers, gently pull on both sides of the plug to release it.
Using either the plastic opening tool or your fingers, gently pull on both sides of the plug to release it.
Step 5
- Remove the battery by grabbing the tab shown and pulling up.
- The battery is held to the device by adhesive. Pull the battery up from the tab and it will lift out with a bit of effort
Remove the battery by grabbing the tab shown and pulling up.
The battery is held to the device by adhesive. Pull the battery up from the tab and it will lift out with a bit of effort
Step 6
- Use an opening tool to pry the speakers out of the tablet.
- The speakers are connected to the tablet by glue and require a lot of prying to remove.
Use an opening tool to pry the speakers out of the tablet.
The speakers are connected to the tablet by glue and require a lot of prying to remove.
Step 7
- Use the plastic opening tool to gently pry up the vibration motor.
Use the plastic opening tool to gently pry up the vibration motor.
Step 8
- Remove the 3.2mm screws using a Phillips #000 screwdriver.
Remove the 3.2mm screws using a Phillips #000 screwdriver.
Step 9
- Flip up the black tab on each connector.
- Pull the ribbon cables out using a plastic opening tool.
Flip up the black tab on each connector.
Pull the ribbon cables out using a plastic opening tool.
Step 10
- Remove the piece of tape by pulling up with your fingers.
Remove the piece of tape by pulling up with your fingers.
Step 11
- Pull up on motherboard gently with fingers and remove.
Pull up on motherboard gently with fingers and remove.
Step 12
- Gently remove the front camera by pulling the ribbon connector out with a plastic opening tool.
Gently remove the front camera by pulling the ribbon connector out with a plastic opening tool.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Dalton Sholders
Member since: 11/07/2019
469 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
IUPUI, Team S3-G5, Harley Fall 2019
Member of IUPUI, Team S3-G5, Harley Fall 2019
IUPUI-HARLEY-F19S3G5
3 Members
2 Guides authored
