Lenovo Ideatab A2109 System Board Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

2

• Battery
• 5 steps
• System Board
• 5 steps

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

• BackLenovo IdeaTab A2109

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Look at the back of the tablet and locate the speakers on top of the rear cover.
• There is a smaller indentation in the plastic cover that runs across the top of the device.
• Wedge the plastic opening tool, under the middle of the cover as shown, then push up and the cover will pop off.

Look at the back of the tablet and locate the speakers on top of the rear cover.

There is a smaller indentation in the plastic cover that runs across the top of the device.

Wedge the plastic opening tool, under the middle of the cover as shown, then push up and the cover will pop off.

1024

Step 2

• Remove SD card if present.
• Remove two black 3mm Phillips #00 screws.

Remove SD card if present.

Remove two black 3mm Phillips #00 screws.

Step 3

• Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing.

Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing.

Step 4

• Remove seven black 3mm Phillips #00 screws.
• The top right corner screw is underneath a yellow ribbon. Lift the ribbon up without disconnecting it and unscrew the screw.

Remove seven black 3mm Phillips #00 screws.

The top right corner screw is underneath a yellow ribbon. Lift the ribbon up without disconnecting it and unscrew the screw.

Step 5

• Now you can take the battery out in order to either replace it or continue disassembling the device.

Now you can take the battery out in order to either replace it or continue disassembling the device.

Step 6

              System Board               

• Remove two black 3mm Phillips #00 screws.
• Remove three silver 1.8 mm Phillips #00 screws.

Remove three silver 1.8 mm Phillips #00 screws.

Step 7

• Use tweezers to flip up the small black plastic locks on all four connections.
• Carefully remove each of the exposed ribbons.

Use tweezers to flip up the small black plastic locks on all four connections.

Carefully remove each of the exposed ribbons.

Step 8

• Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing.

Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing.

Step 9

• Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector.

Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector.

Step 10

• Disconnect the HDMI connection with the system board
• Use a plastic opening tool to pry up the system board, and you will hear a pop as it comes free.
• Slide out the system board from its housing tab on the upper right corner.
• Pull the board slowly away from the tab, and it will pop out.

Disconnect the HDMI connection with the system board

Use a plastic opening tool to pry up the system board, and you will hear a pop as it comes free.

Slide out the system board from its housing tab on the upper right corner.

Pull the board slowly away from the tab, and it will pop out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Kyle                     

Member since: 04/22/2014

581 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Cal Poly, Team 7-19, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 7-19, Regan Spring 2014 



                    CPSU-REGAN-S14S7G19                     


                                            4 Members                     


                                            14 Guides authored