Difficulty
Moderate
Steps
12
Time Required
10 minutes
Sections
3
- Back Panel
- 3 steps
- Battery
- 4 steps
- Trackpad
- 5 steps
Flags
0
BackLenovo IdeaPad Yoga 2 11"
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Begin by turning your closed laptop so that you are looking at the bottom panel.
Begin by turning your closed laptop so that you are looking at the bottom panel.
1024
Step 2
- Locate the 10 screws (6mm) around the border of the panel.
- Using the Torx T5 Screwdriver, remove the screws.
Locate the 10 screws (6mm) around the border of the panel.
Using the Torx T5 Screwdriver, remove the screws.
Step 3
- Now that the screws are removed, gently lift the back panel upwards to detach it from the rest of your laptop.
Now that the screws are removed, gently lift the back panel upwards to detach it from the rest of your laptop.
Step 4
Battery
- Locate the battery in the bottom right corner.
- Using a Phillips #000, remove the 6 screws (3.5mm) on the border of the battery and the 7th screw (6.5mm) that is in the center of the battery.
Locate the battery in the bottom right corner.
Using a Phillips #000, remove the 6 screws (3.5mm) on the border of the battery and the 7th screw (6.5mm) that is in the center of the battery.
Step 5
- Locate the cable connecting to the battery. It is located at the top-center of the battery.
- Use a pair of tweezers and place it so that the tweezer is around the cables. Gently pull the cables towards the battery to disconnect the cable.
Locate the cable connecting to the battery. It is located at the top-center of the battery.
Use a pair of tweezers and place it so that the tweezer is around the cables. Gently pull the cables towards the battery to disconnect the cable.
Step 6
- There may be tape around the edge of the battery to secure some wires. Use a pair of tweezers to remove the tape so that the wires are no longer attached to the battery.
There may be tape around the edge of the battery to secure some wires. Use a pair of tweezers to remove the tape so that the wires are no longer attached to the battery.
Step 7
- After you have unscrewed the screws, unplugged the cable, and removed the tape and wires, you can remove the battery from your laptop.
After you have unscrewed the screws, unplugged the cable, and removed the tape and wires, you can remove the battery from your laptop.
Step 8
Trackpad
- After removing the battery, locate the trackpad of your laptop.
After removing the battery, locate the trackpad of your laptop.
Step 9
- Unscrew 7x 2mm screws holding touchpad in place.
Unscrew 7x 2mm screws holding touchpad in place.
Step 10
- Lift up the plastic cover over the ribbon cable.
Lift up the plastic cover over the ribbon cable.
Step 11
- Gently tug ribbon cable from its position.
Gently tug ribbon cable from its position.
Step 12
- Lift trackpad from the computer.
Lift trackpad from the computer.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Andria Chen
Member since: 10/17/2017
597 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
UC Santa Barbara, Team S1-G5, Weedon Fall 2017
Member of UC Santa Barbara, Team S1-G5, Weedon Fall 2017
UCSB-WEEDON-F17S1G5
5 Members
5 Guides authored
