Difficulty
Easy
Steps
7
Time Required
5 - 10 minutes
Sections
2
- Top Assembly
- 4 steps
- Trackpad
- 3 steps
Flags
0
BackLenovo IdeaPad Yoga 11S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Assembly
- Remember to power off the device before removing any parts.
- Position the laptop so that the bottom enclosure is facing upward.
- Use a Phillips #0 Screwdriver to remove the ten 1.9mm screws holding the bottom enclosure in place.
- Use an opening tool to carefully pry up the rubber pads.
- Use a Phillips screwdriver to remove the two screws under the rubber pads, which secure the keyboard.
Remember to power off the device before removing any parts.
Position the laptop so that the bottom enclosure is facing upward.
Use a Phillips #0 Screwdriver to remove the ten 1.9mm screws holding the bottom enclosure in place.
Use an opening tool to carefully pry up the rubber pads.
Use a Phillips screwdriver to remove the two screws under the rubber pads, which secure the keyboard.
1024
Step 2
Remove Keyboard
- Flip the laptop over and swing open the display.
- Lift the edge of the keyboard closest to the trackpad up.
- Carefully disconnect keyboard ribbon cable from the laptop.
- Remove the keyboard.
Flip the laptop over and swing open the display.
Lift the edge of the keyboard closest to the trackpad up.
Carefully disconnect keyboard ribbon cable from the laptop.
Remove the keyboard.
Step 3
- Remove the two screws securing the midframe.
Remove the two screws securing the midframe.
Step 4
- Grab the front edge of the top assembly and lift it up carefully.
- There are three ribbon cables that attach the top assembly to the motherboard. Lift carefully to avoid damaging them.
- Gently slide the three ribbon cables out of their slots.
- Remove the top assembly completely by pulling it off of the device.
Grab the front edge of the top assembly and lift it up carefully.
There are three ribbon cables that attach the top assembly to the motherboard. Lift carefully to avoid damaging them.
Gently slide the three ribbon cables out of their slots.
Remove the top assembly completely by pulling it off of the device.
Step 5
Trackpad
- Position the removed top encasing where it sits on the keyboard and trackpad. The inside of the top encasing should be upward facing.
- Use a plastic opening tool to lift the retaining flap to disconnect the ZIF connector.
- Gently pull the trackpad cable out of the socket.
Position the removed top encasing where it sits on the keyboard and trackpad. The inside of the top encasing should be upward facing.
Use a plastic opening tool to lift the retaining flap to disconnect the ZIF connector.
Gently pull the trackpad cable out of the socket.
Step 6
- Locate the four 1.6mm screws that connect the trackpad to the top housing.
- Use a Phillips #00 Screwdriver to remove the screws.
Locate the four 1.6mm screws that connect the trackpad to the top housing.
Use a Phillips #00 Screwdriver to remove the screws.
Step 7
- Flip the top assembly over so the keyboard is on top.
- Gently push the trackpad out of its position.
Flip the top assembly over so the keyboard is on top.
Gently push the trackpad out of its position.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Landon Epps
Member since: 03/26/2015
982 Reputation
5 Guides authored
Badges:
19
+16 more badges
Team
Baylor, Team 7-11, Williams Spring 2015
Member of Baylor, Team 7-11, Williams Spring 2015
BU-WILLIAMS-S15S7G11
3 Members
10 Guides authored
