Lenovo Ideapad Y580 2099 Daughterboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Battery
2 steps
Keyboard
3 steps
Daughterboard
9 steps

Flags

BackLenovo IdeaPad Y580-2099
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Slide out both locks for the battery, located on the back of the device.

Slide out both locks for the battery, located on the back of the device.

1024

Step 2

Remove the battery.

Remove the battery.

Step 3

              Keyboard

Unscrew the 2 screws on the bottom of the device.
Slide the back panel out.

Unscrew the 2 screws on the bottom of the device.

Slide the back panel out.

Step 4

Unscrew the 3 “keyboard” detected screws.

Unscrew the 3 “keyboard” detected screws.

Step 5

Flip the laptop over and open up.
Then pry up the whole keyboard using the spudger.
Make sure to use a plastic spudger. You could damage the device using anything else.
Make sure not to take the frame that goes around the keys off. This part is not removable.

Flip the laptop over and open up.

Then pry up the whole keyboard using the spudger.

Make sure to use a plastic spudger. You could damage the device using anything else.

Make sure not to take the frame that goes around the keys off. This part is not removable.

Step 6

              Daughterboard

Use a Phillips #0 screwdriver to remove the 16 screws highlighted. There are 12 M2.5 x 8 mm long screws, and 4 M2 x 2 mm long screws.
Use a Phillips #0 screwdriver to remove the 10 mm screw (highlighted in orange) that secures the disc drive.
Quickly survey and make sure all screws on the back panel are removed from the device.
Some of the screws may have been removed in previous steps.

Use a Phillips #0 screwdriver to remove the 16 screws highlighted. There are 12 M2.5 x 8 mm long screws, and 4 M2 x 2 mm long screws.

Use a Phillips #0 screwdriver to remove the 10 mm screw (highlighted in orange) that secures the disc drive.

Quickly survey and make sure all screws on the back panel are removed from the device.

Some of the screws may have been removed in previous steps.

Step 7

Carefully slide the disc drive out.

Carefully slide the disc drive out.

Step 8

Use a Phillips #0 screwdriver to remove the three M2 x 3 mm long screws circled in red.

Use a Phillips #0 screwdriver to remove the three M2 x 3 mm long screws circled in red.

Step 9

Lift open the top panel carefully as there are wire cables secured to the motherboard.

Lift open the top panel carefully as there are wire cables secured to the motherboard.

Step 10

After locating the cable holding the top panel in place, carefully unhook the handle using precision tweezers.
Carefully remove the top plate.

After locating the cable holding the top panel in place, carefully unhook the handle using precision tweezers.

Carefully remove the top plate.

Step 11

Now that the top plate is removed, locate the daughter board. (Highlighted in Red).

Now that the top plate is removed, locate the daughter board. (Highlighted in Red).

Step 12

Use a plastic spudger or precision tweezers to carefully unhook the daughterboard cables.

Use a plastic spudger or precision tweezers to carefully unhook the daughterboard cables.

Step 13

Use a Phillips #0 screwdriver to remove the two M2.5 x 3 mm long screws that secure the daughterboard.

Use a Phillips #0 screwdriver to remove the two M2.5 x 3 mm long screws that secure the daughterboard.

Step 14

Check and make sure all screws and cable wires are detached before attempting to remove the daughterboard.
Carefully remove the daughterboard.

Check and make sure all screws and cable wires are detached before attempting to remove the daughterboard.

Carefully remove the daughterboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Jeryn Fast

Member since: 04/12/2022

421 Reputation

                                      3 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       IUPUI, Team 1-1, Beck Spring 2022                        

                                                  Member of IUPUI, Team 1-1, Beck Spring 2022 



                    IUPUI-BECK-S22S1G1                     


                                            3 Members                     


                                            3 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team