Lenovo Ideapad Y500 Touchpad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Battery
3 steps
Keyboard
12 steps
Touchpad
3 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackLenovo IdeaPad Y500
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Slide the lock on the right side until you hear a click. Once you hear a click , you should see the color red.

Slide the lock on the right side until you hear a click. Once you hear a click , you should see the color red.

1024

Step 2

Unlike the first lock, this lock is spring loaded and must be held in place when used.
Slide the lock to the left (in the direction of the arrow below the lock) and hold in place.

Unlike the first lock, this lock is spring loaded and must be held in place when used.

Slide the lock to the left (in the direction of the arrow below the lock) and hold in place.

Step 3

Gently pull battery away from the computer while holding open the lock.

Gently pull battery away from the computer while holding open the lock.

Step 4

              Keyboard

Unlock the battery latch by pulling it up.
It should reveal red underneath when it’s unlocked.

Unlock the battery latch by pulling it up.

It should reveal red underneath when it’s unlocked.

Step 5

Push the latch down and then hold in position.
Pull the optical drive out.

Push the latch down and then hold in position.

Pull the optical drive out.

Step 6

Remove nine screws with a Phillips #1 screwdriver.

Remove nine screws with a Phillips #1 screwdriver.

Step 7

Pull up on the loosened cover to remove.
Remove two screws with a Phillips #1 screwdriver.

Pull up on the loosened cover to remove.

Remove two screws with a Phillips #1 screwdriver.

Step 8

Pull the tab straight to the left until part releases.
Lift up the part to remove completely.

Pull the tab straight to the left until part releases.

Lift up the part to remove completely.

Step 9

To release the DIMM, pull the tabs on either side away from each other simultaneously.
The DIMM will pop out on its own.

To release the DIMM, pull the tabs on either side away from each other simultaneously.

The DIMM will pop out on its own.

Step 10

To disconnect the Wi-Fi cables, use a spudger to gently push up under them.
Wi-Fi cables are delicate.

To disconnect the Wi-Fi cables, use a spudger to gently push up under them.

Wi-Fi cables are delicate.

Step 11

Using a Phillips #1 screwdriver, remove the two screws.
Once screws are out, the card will just pop out.

Using a Phillips #1 screwdriver, remove the two screws.

Once screws are out, the card will just pop out.

Step 12

Remove three screws using a Phillips #1 screwdriver.

Remove three screws using a Phillips #1 screwdriver.

Step 13

With the laptop upside down, open slightly.
To remove the keyboard, push the back of the keyboard forward with your thumb while pulling away from the laptop on the other side.
You will not be able to pull the keyboard completely away. The cables are still connected to the laptop.

With the laptop upside down, open slightly.

To remove the keyboard, push the back of the keyboard forward with your thumb while pulling away from the laptop on the other side.

You will not be able to pull the keyboard completely away. The cables are still connected to the laptop.

Step 14

To release the cables, use the spudger to push both ends on the side of the cable.
Gently pull the cables up to disconnect.

To release the cables, use the spudger to push both ends on the side of the cable.

Gently pull the cables up to disconnect.

Step 15

Pull the keyboard up and away from the laptop to remove it.

Pull the keyboard up and away from the laptop to remove it.

Step 16

              Touchpad

Remove a total of 8 screws.
Red circles are m2.5 x 10 mm flathead screws.
Orange circles m2 x 3mm flathead screws.
Yellow circle is m2.5 x 4mm flathead screw.

Remove a total of 8 screws.

Red circles are m2.5 x 10 mm flathead screws.

Orange circles m2 x 3mm flathead screws.

Yellow circle is m2.5 x 4mm flathead screw.

Step 17

Flip up black tabs at the ends of each cable.
With fingers, gently remove the cables underneath from their ports.

Flip up black tabs at the ends of each cable.

With fingers, gently remove the cables underneath from their ports.

Step 18

By unlatching the sides and pulling up, remove the top case from the device.
Casing is fragile, be careful not to twist when pulling up.

By unlatching the sides and pulling up, remove the top case from the device.

Casing is fragile, be careful not to twist when pulling up.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Tatum Hennige

Member since: 04/22/2019

663 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UW Tacoma, Team S1-G2, Cardinal Spring 2019                        

                                                  Member of UW Tacoma, Team S1-G2, Cardinal Spring 2019 



                    UWT-CARDINAL-S19S1G2                     


                                            4 Members                     


                                            5 Guides authored

Better Introduction#

Introduction#

What you need#

Team#

Better Introduction

Introduction

What you need

Team