Difficulty
Moderate
Steps
14
Time Required
5 minutes
Sections
2
- Battery
- 7 steps
- Screen
- 7 steps
Flags
0
BackLenovo IdeaPad U310
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip the device over so the bottom panel is facing up.
- Remove the rubber feet by pinching and pulling in an upward motion.
- The rubber feet are missing from this photo, but will be located within the red markups.
Flip the device over so the bottom panel is facing up.
Remove the rubber feet by pinching and pulling in an upward motion.
The rubber feet are missing from this photo, but will be located within the red markups.
1024
Step 2
- Remove the 4 screws securing the bottom panel to the device.
- The screws are missing from this device and are not pictured. They will be located under the rubber feet within the red markups.
Remove the 4 screws securing the bottom panel to the device.
The screws are missing from this device and are not pictured. They will be located under the rubber feet within the red markups.
Step 3
- Place the plastic opening tool between the bottom panel and device.
- Pry around the device’s outer edge until the bottom panel is no longer attached.
- Lift the bottom panel up and away from device.
Place the plastic opening tool between the bottom panel and device.
Pry around the device’s outer edge until the bottom panel is no longer attached.
Lift the bottom panel up and away from device.
Step 4
- Unplug the Battery from the circuit board by carefully prying the connector from its housing.
Unplug the Battery from the circuit board by carefully prying the connector from its housing.
Step 5
- Remove the 5.6 mm Screw with the PH1 screwdriver.
- Remove the 4.6 mm screws with the PH1 screwdriver.
Remove the 5.6 mm Screw with the PH1 screwdriver.
Remove the 4.6 mm screws with the PH1 screwdriver.
Step 6
- Lift the strip tape away from the battery, being careful not to completely remove it.
Lift the strip tape away from the battery, being careful not to completely remove it.
Step 7
- Remove the battery by lifting up and away from device.
Remove the battery by lifting up and away from device.
Step 8
Screen
- Insert opening tool between the frame and the back panel of the screen.
Insert opening tool between the frame and the back panel of the screen.
Step 9
- Work your way around the frame until every connection is loose.
Work your way around the frame until every connection is loose.
Step 10
- Lift the screen up and away from the device.
- Do not tamper with the tape on the bottom of the screen labeled “Don’t touch”.
Lift the screen up and away from the device.
Do not tamper with the tape on the bottom of the screen labeled “Don’t touch”.
Step 11
- Remove the 1.9 mm screws using the PH0 screwdriver.
- These screws are very short and small, keep track of them.
Remove the 1.9 mm screws using the PH0 screwdriver.
These screws are very short and small, keep track of them.
Step 12
- Once the four screws are removed, gently rest the screen facedown on the keyboard.
Once the four screws are removed, gently rest the screen facedown on the keyboard.
Step 13
- Peel back the white tape, revealing the power connection.
Peel back the white tape, revealing the power connection.
Step 14
- Unplug the connector, pulling it by the white tape.
Unplug the connector, pulling it by the white tape.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Andrew Capra
Member since: 09/28/2016
370 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Eastern Washington University, Team 2-1, Mathisen Fall 2016
Member of Eastern Washington University, Team 2-1, Mathisen Fall 2016
EWU-MATHISEN-F16S2G1
5 Members
5 Guides authored
