Difficulty

Difficult

Steps

27

Time Required

                          1 hour

Sections

11

  • Back Panel
  • 2 steps
  • Battery
  • 3 steps
  • Fan
  • 4 steps
  • Speakers
  • 1 step
  • Hard Drive
  • 1 step
  • RAM
  • 2 steps
  • Heat Sink
  • 1 step
  • Video Cable
  • 1 step
  • Wi-Fi Card
  • 3 steps
  • Motherboard
  • 6 steps
  • Screen
  • 3 steps

Flags

1

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

  • BackLenovo IdeaPad S340-15IWL

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

If your screen fails to turn on, is not displaying images properly, or has been cracked or busted, it may indicate that the screen needs to be replaced.

Make sure you read the troubleshooting page before beginning the replacement as there is a possibility that your device is not charged or that the issue can be resolved without disassembling the device.

Ensure that there is no food or liquid nearby as the device’s internal components will be exposed.

What you need

Step 1

              Back Panel
  • Power off the laptop and place it face-down on a non-scratching surface.
  • Using a Torx T5 screwdriver head, remove all ten 6 mm screws holding the back panel in place.

Power off the laptop and place it face-down on a non-scratching surface.

Using a Torx T5 screwdriver head, remove all ten 6 mm screws holding the back panel in place.

1024

Step 2

  • Slide a plastic opening tool underneath the back case near the screen hinges.
  • Gently pry up on either side of the case.
  • You may hear popping sounds as you pry up the back case. This is normal. If the case does not open, try prying at a different angle/position.

Slide a plastic opening tool underneath the back case near the screen hinges.

Gently pry up on either side of the case.

You may hear popping sounds as you pry up the back case. This is normal. If the case does not open, try prying at a different angle/position.

Step 3

              Battery
  • Remove the three 3 mm screws holding the battery in place using a Phillips #0 screwdriver.

Remove the three 3 mm screws holding the battery in place using a Phillips #0 screwdriver.

Step 4

  • Remove the white and blue bundled wire from the grooves on the right side of the battery.

Remove the white and blue bundled wire from the grooves on the right side of the battery.

Step 5

  • Disconnect the battery cable by gently pulling it straight out of the connector.
  • Be sure to pull parallel to the device to avoid bending the motherboard connector.
  • The battery connector does not lock and only requires light pressure to insert and remove.
  • Remove the battery from the laptop.

Disconnect the battery cable by gently pulling it straight out of the connector.

Be sure to pull parallel to the device to avoid bending the motherboard connector.

The battery connector does not lock and only requires light pressure to insert and remove.

Remove the battery from the laptop.

Step 6

              Fan
  • Remove the two 3 mm screws connecting the fan to the casing using a Phillips #0 screwdriver.

Remove the two 3 mm screws connecting the fan to the casing using a Phillips #0 screwdriver.

Step 7

  • Using a spudger, gently disconnect the fan’s cable from the motherboard.

Using a spudger, gently disconnect the fan’s cable from the motherboard.

Step 8

  • Carefully unwind the black cable that runs between the top of the battery and the bottom of the fan from the grooves along the side of the fan.
  • In order to do so, you will need to pull up the metallic tape that holds the cable in place using either your fingers or a plastic prying tool to lift up the edge.
  • If you attempt to remove the device’s fan without removing the battery, the black cable may be wedged underneath the top of the battery. In this scenario, it is recommended that you at least loosen the screws holding the battery in place to allow for the cable to be removed with less resistance.

Carefully unwind the black cable that runs between the top of the battery and the bottom of the fan from the grooves along the side of the fan.

In order to do so, you will need to pull up the metallic tape that holds the cable in place using either your fingers or a plastic prying tool to lift up the edge.

If you attempt to remove the device’s fan without removing the battery, the black cable may be wedged underneath the top of the battery. In this scenario, it is recommended that you at least loosen the screws holding the battery in place to allow for the cable to be removed with less resistance.

Step 9

  • Carefully pick up the fan by the corners and detach the small connector wire by pulling parallel to the device.
  • Remove the fan from the laptop.

Carefully pick up the fan by the corners and detach the small connector wire by pulling parallel to the device.

Remove the fan from the laptop.

Step 10

              Speakers
  • Unplug the wire connecting the speakers to the motherboard.
  • Remove the speakers from each side of the laptop.

Unplug the wire connecting the speakers to the motherboard.

Remove the speakers from each side of the laptop.

Step 11

              Hard Drive
  • Remove the four 3 mm screws holding the hard drive expansion slot in place using a Phillips #0 screwdriver.

Remove the four 3 mm screws holding the hard drive expansion slot in place using a Phillips #0 screwdriver.

Step 12

              RAM
  • Using the opening tool, gently pop off the metal cover for the RAM stick.

Using the opening tool, gently pop off the metal cover for the RAM stick.

Step 13

  • Using your thumbs, gently pull the two metal prongs that secure the RAM outwards.
  • The RAM will pop up at an angle.
  • Remove the RAM from the laptop.

Using your thumbs, gently pull the two metal prongs that secure the RAM outwards.

The RAM will pop up at an angle.

Remove the RAM from the laptop.

Step 14

              Heat Sink
  • Remove the three 3 mm screws that secure the black heat sink near the top of the computer using a Phillips #0 screwdriver.
  • Lift the heat sink vertically to remove it from the laptop.

Remove the three 3 mm screws that secure the black heat sink near the top of the computer using a Phillips #0 screwdriver.

Lift the heat sink vertically to remove it from the laptop.

Step 15

              Video Cable
  • Using an opening tool, carefully flip up the retaining flaps holding the silver video cable in place.
  • Slide the ribbon cable out of each connector.

Using an opening tool, carefully flip up the retaining flaps holding the silver video cable in place.

Slide the ribbon cable out of each connector.

Step 16

              Wi-Fi Card
  • Pull up the black foam adhesive that covers the screw and connectors holding the Wi-Fi card in place.

Pull up the black foam adhesive that covers the screw and connectors holding the Wi-Fi card in place.

Step 17

  • Using an opening tool, lift up on the black and white coaxial cables on the Wi-Fi card and gently pull upward to unplug them.
  • When reconnecting the cables, be sure to match the colors to the arrows on the Wi-Fi card.

Using an opening tool, lift up on the black and white coaxial cables on the Wi-Fi card and gently pull upward to unplug them.

When reconnecting the cables, be sure to match the colors to the arrows on the Wi-Fi card.

Step 18

  • Remove the single 3 mm screw holding the Wi-Fi card in place using a Phillips #0 screwdriver.
  • Gently lift the Wi-Fi card out of the computer.

Remove the single 3 mm screw holding the Wi-Fi card in place using a Phillips #0 screwdriver.

Gently lift the Wi-Fi card out of the computer.

Step 19

              Motherboard
  • Using an opening tool, flip up the retaining flap that holds the connector to the thin black ribbon cable at the bottom of the motherboard.
  • Gently remove the ribbon cable from its connector.
  • The cable is folded over and connected to itself with an adhesive. Be careful to only pull at the top fold of the cable.

Using an opening tool, flip up the retaining flap that holds the connector to the thin black ribbon cable at the bottom of the motherboard.

Gently remove the ribbon cable from its connector.

The cable is folded over and connected to itself with an adhesive. Be careful to only pull at the top fold of the cable.

Step 20

  • Remove the three total silver 6 mm screws from the hinges of the screen in the top corners of the device using a Phillips #0 screwdriver.

Remove the three total silver 6 mm screws from the hinges of the screen in the top corners of the device using a Phillips #0 screwdriver.

Step 21

  • Use an opening tool to flip up the hinges.
  • You may have to apply some force.

Use an opening tool to flip up the hinges.

You may have to apply some force.

Step 22

  • Remove the three 3 mm screws holding the motherboard in place using a Phillips #0 screwdriver.

Remove the three 3 mm screws holding the motherboard in place using a Phillips #0 screwdriver.

Step 23

  • Carefully unplug the black and red wires connected to the upper right corner of the motherboard.
  • These wires connect to the device’s charging port.

Carefully unplug the black and red wires connected to the upper right corner of the motherboard.

These wires connect to the device’s charging port.

Step 24

  • Carefully lift the motherboard from the base of the computer and remove it from the laptop.

Carefully lift the motherboard from the base of the computer and remove it from the laptop.

Step 25

              Screen
  • Using an opening tool, carefully pry up and remove the plastic bezel casing surrounding the screen.

Using an opening tool, carefully pry up and remove the plastic bezel casing surrounding the screen.

Step 26

  • Using a plastic opening tool, very carefully begin to remove its casing.
  • Be EXTREMELY careful when removing your screen. Make sure that your prying tool is wedged completely under the screen and the foundation holding it in place; it’s easy to accidentally insert the tool into the LCD itself and crack the screen.
  • The screen is held to the casing with a few strips of extremely strong foam adhesive. If possible, it is best to use the prying tool to separate the adhesive from the screen before attempting to remove it.

Using a plastic opening tool, very carefully begin to remove its casing.

Be EXTREMELY careful when removing your screen. Make sure that your prying tool is wedged completely under the screen and the foundation holding it in place; it’s easy to accidentally insert the tool into the LCD itself and crack the screen.

The screen is held to the casing with a few strips of extremely strong foam adhesive. If possible, it is best to use the prying tool to separate the adhesive from the screen before attempting to remove it.

Step 27

  • Lift the display up very carefully.
  • Beneath the electrical tape protecting the circuit board is a small black and gold cable.
  • Gently unplug this cable, and then remove the screen from the casing.

Lift the display up very carefully.

Beneath the electrical tape protecting the circuit board is a small black and gold cable.

Gently unplug this cable, and then remove the screen from the casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Christine Robbins

Member since: 09/17/2021

459 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Western Carolina University, Team 1-3, Virtue Fall 2021                        

                                                  Member of Western Carolina University, Team 1-3, Virtue Fall 2021 



                    WCU-VIRTUE-F21S1G3                     


                                            4 Members                     


                                            5 Guides authored

Yevhen Hrytsenko - Jul 11, 2022

Reply

Hi! thank you! I need to remove the bottom case on this laptop, so after the step 24 I should freely be able to take off the bottom part of the notebook? Thank you