Lenovo Ideapad P400 Touch Ram Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Keyboard
5 steps
Battery
10 steps
RAM
4 steps

Flags

BackLenovo IdeaPad P400 Touch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Keyboard

Remove the two 14mm Phillips #1 screws that attach the keyboard to the underside of the laptop.
Use a Phillips #1 screwdriver.

Remove the two 14mm Phillips #1 screws that attach the keyboard to the underside of the laptop.

Use a Phillips #1 screwdriver.

1024

Step 2

Flip the laptop over and open it as you would to use it.

Flip the laptop over and open it as you would to use it.

Step 3

Using your hands, lift the top corner of the keyboard, and keep lifting until the keyboard pops out. You will hear clicks as you do this.
If necessary, use the plastic spudger to pry up the corner and then lift the keyboard out with your hands.
Do not lift the keyboard out entirely. It will still be connected to the laptop. Only lift it enough so that it is unseated as shown in the second picture.

Using your hands, lift the top corner of the keyboard, and keep lifting until the keyboard pops out. You will hear clicks as you do this.

If necessary, use the plastic spudger to pry up the corner and then lift the keyboard out with your hands.

Do not lift the keyboard out entirely. It will still be connected to the laptop. Only lift it enough so that it is unseated as shown in the second picture.

Step 4

Lift the top of the keyboard and flip the keyboard face down so that you can access the connectors underneath it.
Using your fingers, unplug the large connector that connects the keyboard to the center of the laptop by sliding the end of the strip out of the socket.
You may need to flip the white plastic bar up with a fingernail to be able to remove the strip.

Lift the top of the keyboard and flip the keyboard face down so that you can access the connectors underneath it.

Using your fingers, unplug the large connector that connects the keyboard to the center of the laptop by sliding the end of the strip out of the socket.

You may need to flip the white plastic bar up with a fingernail to be able to remove the strip.

Step 5

Using your fingers, unplug the second, smaller connector, located at the lower left hand side of the keyboard by sliding the strip out of the socket.
You may need to flip the white plastic bar up with your fingernail to remove the connector.

Using your fingers, unplug the second, smaller connector, located at the lower left hand side of the keyboard by sliding the strip out of the socket.

You may need to flip the white plastic bar up with your fingernail to remove the connector.

Step 6

              Battery

Flip the laptop so that the bottom faces up.
You will first need to remove three 7mm Phillips #1 screws from the bottom of the laptop.

Flip the laptop so that the bottom faces up.

You will first need to remove three 7mm Phillips #1 screws from the bottom of the laptop.

Step 7

Using a spudger, remove the back two feet of the laptop.
You may need to use a metal spudger if you cannot remove them with a plastic one.

Using a spudger, remove the back two feet of the laptop.

You may need to use a metal spudger if you cannot remove them with a plastic one.

Step 8

Remove the 7mm Phillips #1 screw beneath where the foot was. Do this for both sides.

Remove the 7mm Phillips #1 screw beneath where the foot was. Do this for both sides.

Step 9

Flip the laptop over and open it.
Remove the 3mm Phillips #1 screw holding the disc drive in place.
Remove the disc drive by sliding it out.

Flip the laptop over and open it.

Remove the 3mm Phillips #1 screw holding the disc drive in place.

Remove the disc drive by sliding it out.

Step 10

Remove four 7mm Phillips #1 interior screws.

Remove four 7mm Phillips #1 interior screws.

Step 11

Close the laptop lid and flip it over.
Remove three 3mm Phillips #1 screws from beneath where the disc drive was located.

Close the laptop lid and flip it over.

Remove three 3mm Phillips #1 screws from beneath where the disc drive was located.

Step 12

Using a plastic spudger, pry open the laptop case starting near the disc drive.
Continue prying open the case by using the spudger to open it in new areas.
Once there is enough space to allow you to grip the case, use your hands to finish removing it.
It may be difficult at first. If the plastic spudger does not work, you can try using a metal one. Using a hand to pull the case open while prying may help as well.

Using a plastic spudger, pry open the laptop case starting near the disc drive.

Continue prying open the case by using the spudger to open it in new areas.

Once there is enough space to allow you to grip the case, use your hands to finish removing it.

It may be difficult at first. If the plastic spudger does not work, you can try using a metal one. Using a hand to pull the case open while prying may help as well.

Step 13

Using your fingers, unplug the battery from the laptop by taking the plug out of its socket.

Using your fingers, unplug the battery from the laptop by taking the plug out of its socket.

Step 14

Unscrew the battery from the laptop by removing two 3mm Phillips #1 screws.

Unscrew the battery from the laptop by removing two 3mm Phillips #1 screws.

Step 15

Using your hand, remove the battery from the laptop by lifting one side and then pulling it out of its slot.

Using your hand, remove the battery from the laptop by lifting one side and then pulling it out of its slot.

Step 16

RAM

Pull outward on both clips on the sides of the top RAM to release it.
The RAM will pop up slightly if you have pulled the clips out properly.

Pull outward on both clips on the sides of the top RAM to release it.

The RAM will pop up slightly if you have pulled the clips out properly.

Step 17

Remove the top RAM from its slot by sliding it out.

Remove the top RAM from its slot by sliding it out.

Step 18

Pull outward on both clips on the sides of the bottom RAM to release it.
The RAM will pop up slightly if you have pulled the clips out properly.

Pull outward on both clips on the sides of the bottom RAM to release it.

Step 19

Remove the bottom RAM from its slot by sliding it out.

Remove the bottom RAM from its slot by sliding it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Stephanie Botica

Member since: 10/30/2017

841 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       University of North Texas, Team S1-G1, Boettger Fall 2017                        

                                                  Member of University of North Texas, Team S1-G1, Boettger Fall 2017 



                    UNT-BOETTGER-F17S1G1                     


                                            2 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team