Difficulty

Difficult

Steps

10

Time Required

                          2 hours

Sections

1

  • Screen Assembly
  • 10 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackLenovo IdeaPad 530S-14IKB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Remove the bottom cover
  • Unscrew all 10 T5 screws. The screws are all the same length.
  • Remove the bottom cover carefully. Maybe it is necessary to use a pick or spudger.

Unscrew all 10 T5 screws. The screws are all the same length.

Remove the bottom cover carefully. Maybe it is necessary to use a pick or spudger.

1024

Step 2

              Disconnect the battery
  • Disconnect the battery off the main board.

Disconnect the battery off the main board.

Step 3

              Disconnect the antenna cables and mainboard
  • Disconnect antenna cable 1 and 2 und pull them out of their holding.

Disconnect antenna cable 1 and 2 und pull them out of their holding.

Step 4

              Disconnect the display and mainboard
  • Open the black lever on the display connection and carefully pull out the ribbon cable parallel to the mainboard. Do NOT pull upwards!

Open the black lever on the display connection and carefully pull out the ribbon cable parallel to the mainboard. Do NOT pull upwards!

Step 5

              Separate the display assembly
  • Open the laptop in a 90 degree angle. Unscrew the 4 PH0 screws (all the same length).
  • Carefully separate the display and chassis. Take special care with the antenna cables and display ribbon cable.

Open the laptop in a 90 degree angle. Unscrew the 4 PH0 screws (all the same length).

Carefully separate the display and chassis. Take special care with the antenna cables and display ribbon cable.

Step 6

              Separate the covers on the display
  • Move the plastic cover from left to right. This might take a little bit of force.
  • It clicks and is easily removed afterwards.
  • The coverstrip underneath can be removed with a spudger.

Move the plastic cover from left to right. This might take a little bit of force.

It clicks and is easily removed afterwards.

The coverstrip underneath can be removed with a spudger.

Step 7

              Separate the display assembly of the enclosure
  • Unscrew the highlighted two PH000 screws (same length).
  • Pull out the pull tabs from underneath the display assembly. Take your time and pull very carefully and even.
  • ATTENTION: Always grasp the pull tab as near to the display as possible. Like this you avoid tearing it.

Unscrew the highlighted two PH000 screws (same length).

Pull out the pull tabs from underneath the display assembly. Take your time and pull very carefully and even.

ATTENTION: Always grasp the pull tab as near to the display as possible. Like this you avoid tearing it.

Step 8

              Lift the display assembly from the enclosure
  • Carfully push down on the display while pushing it in the direction of the arrows.
  • Lift up the display assembly just a few millimeters and then push it further in the direction oft the arrows to unclick the display assembly from the enclosure. Finally you can without force lift up the display in a 90 degree angle.

Carfully push down on the display while pushing it in the direction of the arrows.

Lift up the display assembly just a few millimeters and then push it further in the direction oft the arrows to unclick the display assembly from the enclosure. Finally you can without force lift up the display in a 90 degree angle.

Step 9

              Disconnect the display assembly and enclosure
  • Disconnect the 30 pole ribbon cable of the display assembly. To do that you have to open the connection with the small metal lever. After opening it you can pull the ribbon cable straight down.

Disconnect the 30 pole ribbon cable of the display assembly. To do that you have to open the connection with the small metal lever. After opening it you can pull the ribbon cable straight down.

Step 10

              Put in the new display assembly
  • Apply the new pull tabs so that you can easily replace the screen again.
  • To reassemble your device, follow these instructions in reverse order.

Apply the new pull tabs so that you can easily replace the screen again.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        Leonard Pitt Diehl is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Leonard Pitt Diehl

Author

                                      with 1 other contributor 


                    Leonard Pitt Diehl

Member since: 01/04/2020

311 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges