Difficulty

Moderate

Steps

12

Time Required

                          5 - 10 minutes

Sections

3

  • DVD/CD Optical Drive
  • 3 steps
  • Battery
  • 6 steps
  • Speaker
  • 3 steps

Flags

0

  • BackLenovo IdeaPad 130-15AST

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              DVD/CD Optical Drive
  • Verify that the DVD/CD Tray is free of DVD’s and CD’s.
  • Using a Phillips #00 screwdriver, remove one of the 6.0mm screws.

Verify that the DVD/CD Tray is free of DVD’s and CD’s.

Using a Phillips #00 screwdriver, remove one of the 6.0mm screws.

1024

Step 2

  • Using the Jimmy Tool, gently pry the DVD/CD Drive away from the case of the laptop.

Using the Jimmy Tool, gently pry the DVD/CD Drive away from the case of the laptop.

Step 3

  • Gently slide the DVD/CD Drive out of the laptop.

Gently slide the DVD/CD Drive out of the laptop.

Step 4

              Battery
  • Before proceeding, make sure the computer is turned off and it is not connected to any power source.
  • Using a Phillips #00 screwdriver, remove twelve of the 6.0mm screws.

Before proceeding, make sure the computer is turned off and it is not connected to any power source.

Using a Phillips #00 screwdriver, remove twelve of the 6.0mm screws.

Step 5

  • Do not try to completely remove this case without ensuring the entire case is free of connection points as this could crack or damage the case.
  • Use a thin, flat edge to gently break the seal of the case.

Do not try to completely remove this case without ensuring the entire case is free of connection points as this could crack or damage the case.

Use a thin, flat edge to gently break the seal of the case.

Step 6

  • Make sure that the back panel is completely free from the laptop.
  • Grab the sides of the back panel of the laptop with two hands. Then separate the panel from the laptop by lifting up.

Make sure that the back panel is completely free from the laptop.

Grab the sides of the back panel of the laptop with two hands. Then separate the panel from the laptop by lifting up.

Step 7

  • Using a Phillips #0 screwdriver, remove three 6.0mm screws.

Using a Phillips #0 screwdriver, remove three 6.0mm screws.

Step 8

  • Using a pair of tweezers, remove the black plug which includes 8 wires.

Using a pair of tweezers, remove the black plug which includes 8 wires.

Step 9

  • Grabbing the sides of the battery with one hand, remove the battery from the laptop.

Grabbing the sides of the battery with one hand, remove the battery from the laptop.

Step 10

              Speaker
  • Using a prying tool, remove the white plug (which includes 4 different colored wires) from the motherboard. Repeat the same step for the other plug.
  • This plug is small and fragile. You should not use a lot of force to separate the plastic connection from the motherboard.

Using a prying tool, remove the white plug (which includes 4 different colored wires) from the motherboard. Repeat the same step for the other plug.

This plug is small and fragile. You should not use a lot of force to separate the plastic connection from the motherboard.

Step 11

  • Disconnect the speaker wires from their connection tabs along the front of the computer.
  • These wires are not connected to anything internally. They connect the speakers from the power supply to each other.

Disconnect the speaker wires from their connection tabs along the front of the computer.

These wires are not connected to anything internally. They connect the speakers from the power supply to each other.

Step 12

  • To remove the speakers, pinch the inside edge and lift upwards.
  • These speakers are help in by O-rings. Be sure not to lose these, as new speakers do not come with new O-rings.

To remove the speakers, pinch the inside edge and lift upwards.

These speakers are help in by O-rings. Be sure not to lose these, as new speakers do not come with new O-rings.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Wesley Atteberry

Member since: 09/22/2019

193 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Embry-Riddle Aeronautical University, Team S12-G3, Lamothe Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S12-G3, Lamothe Fall 2019 



                    ERAU-LAMOTHE-F19S12G3                     


                                            4 Members                     


                                            5 Guides authored