Difficulty
Difficult
Steps
12
Time Required
30 minutes
Sections
4
- Keyboard
- 3 steps
- Optical Drive
- 2 steps
- Upper Case
- 2 steps
- Motherboard
- 5 steps
Flags
0
BackLenovo IdeaPad 110-15ISK
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Keyboard
- Flip the IdeaPad bottom side up.
- Using a Phillips #1 screwdriver, remove the two 6.0mm screws on the back panel, that hold the keyboard.
- Flip the computer back to top facing.
Flip the IdeaPad bottom side up.
Using a Phillips #1 screwdriver, remove the two 6.0mm screws on the back panel, that hold the keyboard.
Flip the computer back to top facing.
1024
Step 2
- Open the lid.
- Use the plastic opening tool to pry the keyboard up and away from the bottom assembly.
Open the lid.
Use the plastic opening tool to pry the keyboard up and away from the bottom assembly.
Step 3
- Next disconnect the keyboard cable by using the tip of the spudger or your finger to lightly push out the ribbon from the contact port.
- Completely remove the keyboard from the bottom assembly.
Next disconnect the keyboard cable by using the tip of the spudger or your finger to lightly push out the ribbon from the contact port.
Completely remove the keyboard from the bottom assembly.
Step 4
Optical Drive
- Using a Phillips #1 screwdriver, unscrew the one 5.0mm screw on the back panel.
Using a Phillips #1 screwdriver, unscrew the one 5.0mm screw on the back panel.
Step 5
- Flip the laptop to its back and the optical drive is located at the top left corner.
- Remove the optical CD DVD drive by lightly pulling it out of the assembly.
Flip the laptop to its back and the optical drive is located at the top left corner.
Remove the optical CD DVD drive by lightly pulling it out of the assembly.
Step 6
Upper Case
- Place the laptop bottom facing up.
- Using a Phillips #1 screwdriver, remove the remaining eight 6.0mm screws on the back panel.
- Flip the computer back to top facing.
Place the laptop bottom facing up.
Using a Phillips #1 screwdriver, remove the remaining eight 6.0mm screws on the back panel.
Step 7
- Separate the top case from the bottom using a plastic opening tool.
- Continue prying the top and bottom case from each other all around the perimeter of the laptop.
Separate the top case from the bottom using a plastic opening tool.
Continue prying the top and bottom case from each other all around the perimeter of the laptop.
Step 8
Motherboard
- Pull the two connectors with blue ribbons marked with MB in the opposite direction of the connector
Pull the two connectors with blue ribbons marked with MB in the opposite direction of the connector
Step 9
- Using a Phillips #1 screwdriver, remove the marked four 4.0mm screws.
- Pull out the hard drive.
Using a Phillips #1 screwdriver, remove the marked four 4.0mm screws.
Pull out the hard drive.
Step 10
- Using a Phillips #1 screwdriver, remove the five 4.0mm screws.
Using a Phillips #1 screwdriver, remove the five 4.0mm screws.
Step 11
- Using tweezers, pull the four marked connectors out and away from the motherboard.
- Remove the WIFI card by pulling up and away from the motherboard.
Using tweezers, pull the four marked connectors out and away from the motherboard.
Remove the WIFI card by pulling up and away from the motherboard.
Step 12
- Pull off the motherboard.
Pull off the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Jakub Szark
Member since: 10/17/2018
513 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
UW Tacoma, Team S1-G5, Rose Fall 2018
Member of UW Tacoma, Team S1-G5, Rose Fall 2018
UWT-ROSE-F18S1G5
4 Members
35 Guides authored
