Difficulty

Easy

Steps

11

Time Required

                          5 minutes

Sections

5

  • Keyboard
  • 3 steps
  • Optical Drive
  • 2 steps
  • Upper Case
  • 2 steps
  • Battery
  • 2 steps
  • Hard Drive
  • 2 steps

Flags

0

  • BackLenovo IdeaPad 110-15ISK

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard
  • Flip the IdeaPad bottom side up.
  • Using a Phillips #1 screwdriver, remove the two 6.0mm screws on the back panel, that hold the keyboard.
  • Flip the computer back to top facing.

Flip the IdeaPad bottom side up.

Using a Phillips #1 screwdriver, remove the two 6.0mm screws on the back panel, that hold the keyboard.

Flip the computer back to top facing.

1024

Step 2

  • Open the lid.
  • Use the plastic opening tool to pry the keyboard up and away from the bottom assembly.

Open the lid.

Use the plastic opening tool to pry the keyboard up and away from the bottom assembly.

Step 3

  • Next disconnect the keyboard cable by using the tip of the spudger or your finger to lightly push out the ribbon from the contact port.
  • Completely remove the keyboard from the bottom assembly.

Next disconnect the keyboard cable by using the tip of the spudger or your finger to lightly push out the ribbon from the contact port.

Completely remove the keyboard from the bottom assembly.

Step 4

              Optical Drive
  • Using a Phillips #1 screwdriver, unscrew the one 5.0mm screw on the back panel.

Using a Phillips #1 screwdriver, unscrew the one 5.0mm screw on the back panel.

Step 5

  • Flip the laptop to its back and the optical drive is located at the top left corner.
  • Remove the optical CD DVD drive by lightly pulling it out of the assembly.

Flip the laptop to its back and the optical drive is located at the top left corner.

Remove the optical CD DVD drive by lightly pulling it out of the assembly.

Step 6

              Upper Case
  • Place the laptop bottom facing up.
  • Using a Phillips #1 screwdriver, remove the remaining eight 6.0mm screws on the back panel.
  • Flip the computer back to top facing.

Place the laptop bottom facing up.

Using a Phillips #1 screwdriver, remove the remaining eight 6.0mm screws on the back panel.

Step 7

  • Separate the top case from the bottom using a plastic opening tool.
  • Continue prying the top and bottom case from each other all around the perimeter of the laptop.

Separate the top case from the bottom using a plastic opening tool.

Continue prying the top and bottom case from each other all around the perimeter of the laptop.

Step 8

              Battery
  • Turn the laptop upside down and gently pry the top case free from the bottom case.

Turn the laptop upside down and gently pry the top case free from the bottom case.

Step 9

  • The battery is attached to the bottom case of the laptop.
  • Remove the two 4.0mm screws.
  • Push the battery component away from you in order to completely remove the battery from the fixture.

The battery is attached to the bottom case of the laptop.

Remove the two 4.0mm screws.

Push the battery component away from you in order to completely remove the battery from the fixture.

Step 10

              Hard Drive
  • Using a Phillips #1 screwdriver, remove the four 4.0mm corner screws securing the hard drive assembly to the body.
  • Disconnect the hard drive from the back panel by sliding it to the left until loosened.
  • Remove it completely by lifting the hard drive out of the back panel.

Using a Phillips #1 screwdriver, remove the four 4.0mm corner screws securing the hard drive assembly to the body.

Disconnect the hard drive from the back panel by sliding it to the left until loosened.

Remove it completely by lifting the hard drive out of the back panel.

Step 11

  • Using the Phillips #1 screwdriver, remove the four 3.0mm corner screws from the caddy of the hard drive.
  • Separate the plastic caddy from the hard drive.

Using the Phillips #1 screwdriver, remove the four 3.0mm corner screws from the caddy of the hard drive.

Separate the plastic caddy from the hard drive.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 4 other contributors 


                    Jakub Szark

Member since: 10/17/2018

513 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UW Tacoma, Team S1-G5, Rose Fall 2018                        

                                                  Member of UW Tacoma, Team S1-G5, Rose Fall 2018 



                    UWT-ROSE-F18S1G5                     


                                            4 Members                     


                                            35 Guides authored

et_rc992@etheli.com - Oct 25, 2020

Reply

I found that two of the screws on the bottom hold down the keyboard, so they need to be unscrewed before the keyboard will come up. Also, there are two “shallow” screws (that become visible after the DVD drive is removed) which need to be removed, and the battery doesn’t really need to be removed to replace the hard drive.

Michael Wiseman - Jan 21, 2021

Reply

Teresa Mcgervey - Apr 28, 2022

Reply

Cannot remove optical hard drive following instructions. Does not appear to be removable on my Lenovo Ideapad 110.

dsjh68 - Apr 30, 2022

Reply

Yes I have same problem and cannot remove the optical drive from my Lenovo Ideapad 110! Trying to add memory and can’t do that until the optical drive is removed! Wth!