Lenovo G50 80 80E5 Usb Port Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

Suggest a time??

Sections

Motherboard
14 steps
USB Port
2 steps

Flags

BackLenovo G50-80 80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Motherboard

From the underside of the laptop, press the two battery tabs inward to remove the battery. Lift the battery to remove.

From the underside of the laptop, press the two battery tabs inward to remove the battery. Lift the battery to remove.

1024

Step 2

Remove the three #00x5.5mm screws from the bottom front under panel and then slide the main access panel forward and out.

Remove the three #00x5.5mm screws from the bottom front under panel and then slide the main access panel forward and out.

Step 3

Remove the two #00x4.5mm screws from the hard drive and then slide the drive to the side and remove the hard drive.

Remove the two #00x4.5mm screws from the hard drive and then slide the drive to the side and remove the hard drive.

Step 4

Remove the three #00x5.5mm screws from the fan unit, unplug the fan wiring connector and then remove the fan unit.

Remove the three #00x5.5mm screws from the fan unit, unplug the fan wiring connector and then remove the fan unit.

Step 5

Use tweezers to carefully remove the white and black wires from the WiFi card. Thread the wires back out of it’s channel and hold to the side.

Use tweezers to carefully remove the white and black wires from the WiFi card. Thread the wires back out of it’s channel and hold to the side.

Step 6

Unplug the two ribbon cables from under the fan unit area.

Unplug the two ribbon cables from under the fan unit area.

Step 7

Remove the CD Drive fixing screw (#00x5.5mm) and slide the drive out from it’s slot.

Remove the CD Drive fixing screw (#00x5.5mm) and slide the drive out from it’s slot.

Step 8

Release the RAM fixing clip from both ends of each RAM chip. Once released, slide out each RAM chip.

Release the RAM fixing clip from both ends of each RAM chip. Once released, slide out each RAM chip.

Step 9

Remove the three #00x5.5mm screws holding the keyboard.

Remove the three #00x5.5mm screws holding the keyboard.

Step 10

Remove the six perimeter #00x5.5mm screws holding the palm rest.

Remove the six perimeter #00x5.5mm screws holding the palm rest.

Step 11

Flip the laptop over, lift the screen and with a plastic spudger begin to remove the keyboard. Start at the top left corner and work from left to right lifting the keyboard. Once the top section is free, lift the keyboard up and away from yourself. Remove the ribbon cable connection and set the keyboard aside.

Flip the laptop over, lift the screen and with a plastic spudger begin to remove the keyboard. Start at the top left corner and work from left to right lifting the keyboard. Once the top section is free, lift the keyboard up and away from yourself. Remove the ribbon cable connection and set the keyboard aside.

Step 12

Disconnect the two ribbon cables then using a plastic spudger, begin to separate the the palm rest from the chassis. Start along the front left edge and work left to right to separate each half. Separate the left and right sides in the same fashion.

Disconnect the two ribbon cables then using a plastic spudger, begin to separate the the palm rest from the chassis. Start along the front left edge and work left to right to separate each half. Separate the left and right sides in the same fashion.

Step 13

Disconnect the CD Drive ribbon cable and the auxiliary board cable. Disconnect the speaker cable and then remove the CD Drive board fixing screw (#00x4.5mm). Remove the auxiliary board fixing screw and then remove the auxiliary board.

Disconnect the CD Drive ribbon cable and the auxiliary board cable. Disconnect the speaker cable and then remove the CD Drive board fixing screw (#00x4.5mm). Remove the auxiliary board fixing screw and then remove the auxiliary board.

Step 14

Remove the three motherboard fixing screws (#00x5.5mm) and remove the motherboard.

Remove the three motherboard fixing screws (#00x5.5mm) and remove the motherboard.

Step 15

              USB Port

These joints will have to be soldered for removal

These joints will have to be soldered for removal

Step 16

How To Solder and Desolder Connections

How To Solder and Desolder Connections

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Victor

Member since: 10/17/2017

1,184 Reputation

                                      4 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       UMass Dartmouth, Team S1-G6, Simcock Fall 2017                        

                                                  Member of UMass Dartmouth, Team S1-G6, Simcock Fall 2017 



                    UMASSD-SIMCOCK-F17S1G6                     


                                            4 Members                     


                                            10 Guides authored

Bartosz Baranowski - Aug 11, 2019

What kind of port is this? THT/SMD? THT even or scrambled( offset ) set of THT elements? Four latch pins make it look like: https://cy.rsdelivers.com/product/wurth-…

Introduction#

What you need#

Team#

Introduction

What you need

Team