Difficulty

Moderate

Steps

10

Time Required

                          15 minutes

Sections

2

  • Battery
  • 6 steps
  • Motherboard
  • 4 steps

Flags

1

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackLeapFrog LeapPad Ultra

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the barcode covering the two screws on the lower back of the Leap Pad.

Remove the barcode covering the two screws on the lower back of the Leap Pad.

1024

Step 2

  • Remove the two 5 mm screws that were covered by the sticker.

Remove the two 5 mm screws that were covered by the sticker.

Step 3

  • Using a plastic opening tool, pry off the outer protective child proof casing, starting from the bottom.

Using a plastic opening tool, pry off the outer protective child proof casing, starting from the bottom.

Step 4

  • Remove the 7 mm screw to the right of the cartridge dock, two 8 mm screws in the top left, and the nine 8 mm screws holding the the green shell.

Remove the 7 mm screw to the right of the cartridge dock, two 8 mm screws in the top left, and the nine 8 mm screws holding the the green shell.

Step 5

  • Remove the hard plastic casing, exposing the motherboard and battery.

Remove the hard plastic casing, exposing the motherboard and battery.

Step 6

  • Disconnect the battery using tweezers or your fingernails.
  • The battery is glued down, if available put some isopropyl alcohol around the edges of the battery to soften the glue.
  • Gently pry of the battery lose using a spudger or another thin prying tool.
  • Be careful, damaging/puncturing the battery may cause an explosion.

Disconnect the battery using tweezers or your fingernails.

The battery is glued down, if available put some isopropyl alcohol around the edges of the battery to soften the glue.

Gently pry of the battery lose using a spudger or another thin prying tool.

Be careful, damaging/puncturing the battery may cause an explosion.

Step 7

              Motherboard
  • Disconnect the three wires that will be visible on top of the motherboard. The wires need to be disconnected by pulling them up vertically.

Disconnect the three wires that will be visible on top of the motherboard. The wires need to be disconnected by pulling them up vertically.

Step 8

  • Unscrew the five screws holding the motherboard into the housing.

Unscrew the five screws holding the motherboard into the housing.

Step 9

  • Lift the motherboard up exposing the fourth and final wire. Once you lift up the motherboard you will need to pull down on the wire to disconnect.

Lift the motherboard up exposing the fourth and final wire. Once you lift up the motherboard you will need to pull down on the wire to disconnect.

Step 10

  • Remove and replace motherboard.

Remove and replace motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Rocky Hirsch

Member since: 08/27/2015

848 Reputation

                                      3 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

Team

                       USF Tampa, Team 4-99, Meier Fall 2015                        

                                                  Member of USF Tampa, Team 4-99, Meier Fall 2015 



                    USFT-MEIER-F15S4G99                     


                                            4 Members                     


                                            10 Guides authored