Difficulty

Moderate

Steps

6

Time Required

                          20 minutes

Sections

2

  • Back Panel
  • 2 steps
  • Motherboard
  • 4 steps

Flags

0

  • BackLeapFrog LeapPad Ultimate

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Flip over the Pad to its back side to begin the removal of the back panel.
  • Begin by removing the blue rim along the edge of the device. It runs along the green silicone lining.
  • This is very difficult to remove , so do be patient. To help remove the seal, both a metal spudger and plastic opening tool may be used.
  • Remove the pen from its place before starting to avoid tangling.

Flip over the Pad to its back side to begin the removal of the back panel.

Begin by removing the blue rim along the edge of the device. It runs along the green silicone lining.

This is very difficult to remove , so do be patient. To help remove the seal, both a metal spudger and plastic opening tool may be used.

Remove the pen from its place before starting to avoid tangling.

1024

Step 2

  • Once the blue rim is removed, the 12 screws will be visible.
  • Use the Phillips #1 screwdriver to unscrew all 12 screws.

Once the blue rim is removed, the 12 screws will be visible.

Use the Phillips #1 screwdriver to unscrew all 12 screws.

Step 3

              Motherboard
  • Begin with the removal of the battery from its place.
  • Flip the black switch that is connecting the battery to the motherboard.
  • Then pull gently and should disconnect.

Begin with the removal of the battery from its place.

Flip the black switch that is connecting the battery to the motherboard.

Then pull gently and should disconnect.

Step 4

  • Remove the black and white ribbon structures from the side of the motherboard.
  • Next, remove the three screws along the corners of the motherboard using the Phillips # 1 screwdriver.

Remove the black and white ribbon structures from the side of the motherboard.

Next, remove the three screws along the corners of the motherboard using the Phillips # 1 screwdriver.

Step 5

  • Use a Phillips #1 screwdriver to unscrew the 7 screws from the speaker with the bronze plate sound board.
  • Unscrew the 8 screws from the blue sub-panel.

Use a Phillips #1 screwdriver to unscrew the 7 screws from the speaker with the bronze plate sound board.

Unscrew the 8 screws from the blue sub-panel.

Step 6

  • Take off the sub-panel exposing the motherboard.
  • Flip the motherboard on its back side and flip the switch to remove the wide orange ribbon and pull the twisted black and white wires from its place.

Take off the sub-panel exposing the motherboard.

Flip the motherboard on its back side and flip the switch to remove the wide orange ribbon and pull the twisted black and white wires from its place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Fernando Lozano-Garcia

Member since: 09/21/2018

356 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       University of North Texas, Team S1-G13, Riccardelli Fall 2018                        

                                                  Member of University of North Texas, Team S1-G13, Riccardelli Fall 2018 



                    UNT-RICCARDELLI-F18S1G13                     


                                            4 Members                     


                                            12 Guides authored