Difficulty
Moderate
Steps
9
Time Required
15 - 20 minutes
Sections
2
- Battery
- 2 steps
- Motherboard
- 7 steps
Flags
0
BackKyocera Zio M6000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Press down on the back of the phone, applying moderate pressure.
- Slide the back casing down to separate it.
Press down on the back of the phone, applying moderate pressure.
Slide the back casing down to separate it.
1024
Step 2
- Remove the back casing to expose the battery.
- Use a plastic spudger to lift the battery out using the battery’s groove on its top left corner.
Remove the back casing to expose the battery.
Use a plastic spudger to lift the battery out using the battery’s groove on its top left corner.
Step 3
Motherboard
- Remove the six 3.18 mm screws using a Phillips 00 screwdriver.
Remove the six 3.18 mm screws using a Phillips 00 screwdriver.
Step 4
- Insert the flat end of the spudger between the front and back panels, and pry it apart by running the spudger along the side to further separate them.
- Go all the way around, prying as you go, until the back casing completely separates from the rest of the phone.
Insert the flat end of the spudger between the front and back panels, and pry it apart by running the spudger along the side to further separate them.
Go all the way around, prying as you go, until the back casing completely separates from the rest of the phone.
Step 5
- Unclip the two flex cables – a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up.
Unclip the two flex cables – a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up.
Step 6
- Pry out the earpiece speaker using the spudger.
- Pry out the vibration motor using the spudger.
Pry out the earpiece speaker using the spudger.
Pry out the vibration motor using the spudger.
Step 7
- Place the flat end of the spudger underneath the digitizer connector and pry it up to disconnect it.
Place the flat end of the spudger underneath the digitizer connector and pry it up to disconnect it.
Step 8
- Remove the sticker to uncover the screws underneath.
- Remove the six 1.59 mm screws using a Phillips 00 screwdriver.
Remove the sticker to uncover the screws underneath.
Remove the six 1.59 mm screws using a Phillips 00 screwdriver.
Step 9
- Lift the bottom portion of the motherboard away from the front panel.
- Do not forcefully pull the components apart as there is another connector on the underside of the motherboard attaching it to the panel.
- Insert the flat end of the spudger in between the panel and motherboard to unfasten the connector.
Lift the bottom portion of the motherboard away from the front panel.
Do not forcefully pull the components apart as there is another connector on the underside of the motherboard attaching it to the panel.
Insert the flat end of the spudger in between the panel and motherboard to unfasten the connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Scott Nguyen
Member since: 09/16/2015
522 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
USF Sarasota-Manatee, Team 1-2, Stewart Fall 2015
Member of USF Sarasota-Manatee, Team 1-2, Stewart Fall 2015
USFSM-STEWART-F15S1G2
5 Members
16 Guides authored
