Kurio 7 Motherboard Removal Guide Repair Guide

Difficulty

Difficult

Steps

Time Required

                          15 - 25 minutes

Sections

Back Panel
4 steps
Kurio 7 Motherboard Removal Guide
5 steps

Flags

BackKurio 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Begin by removing the rubber cover from the Kurio 7.

Begin by removing the rubber cover from the Kurio 7.

1024

Step 2

Remove the four 30 mm Phillips #00 screws from the outer case.

Remove the four 30 mm Phillips #00 screws from the outer case.

Step 3

Insert the plastic opening tool in the gap between the front cover and the back cover of the device.
Slide the plastic opening tool around the edge of the device. Gently pry apart the tabs that hold the front cover and the back cover together.
Be careful not to break off the tabs that hold the front cover and the back cover together.

Insert the plastic opening tool in the gap between the front cover and the back cover of the device.

Slide the plastic opening tool around the edge of the device. Gently pry apart the tabs that hold the front cover and the back cover together.

Be careful not to break off the tabs that hold the front cover and the back cover together.

Step 4

Once all of the tabs are removed, the back cover should come off easily.
Gently remove the back cover. There are wires inside that may get caught on the cover while removing it. These wires are soldered to their components and are difficult to reattach.

Once all of the tabs are removed, the back cover should come off easily.

Gently remove the back cover. There are wires inside that may get caught on the cover while removing it. These wires are soldered to their components and are difficult to reattach.

Step 5

              Kurio 7 Motherboard Removal Guide

Use a plastic credit card, or other thin object, to separate the battery from the screen.
Be sure to work the card carefully and slowly around in order to not damage, break, or deform the battery.
Carefully set the battery aside.

Use a plastic credit card, or other thin object, to separate the battery from the screen.

Be sure to work the card carefully and slowly around in order to not damage, break, or deform the battery.

Carefully set the battery aside.

Step 6

Use a Phillips #00 screwdriver to remove the eight 40mm screws holding the motherboard in place.

Use a Phillips #00 screwdriver to remove the eight 40mm screws holding the motherboard in place.

Step 7

Place the plastic opening tool on the base of the black ribbon clip and pull up, like a lever, to release the mount. This should release the clip holding the ribbon to the mount.
Pull the ribbon out of the mount.

Place the plastic opening tool on the base of the black ribbon clip and pull up, like a lever, to release the mount. This should release the clip holding the ribbon to the mount.

Pull the ribbon out of the mount.

Step 8

There should be masking tape on the yellow ribbon. Pull the tape off of the motherboard and wrap it around the yellow ribbon.
Do not pull the tape completely off the motherboard, as it is used to protect components on the ribbon.
To remove the ribbon from the mount, follow the same steps in Step 3.

There should be masking tape on the yellow ribbon. Pull the tape off of the motherboard and wrap it around the yellow ribbon.

Do not pull the tape completely off the motherboard, as it is used to protect components on the ribbon.

To remove the ribbon from the mount, follow the same steps in Step 3.

Step 9

Pull back the ribbons and put the battery near the bottom of the Kurio.
The motherboard is now removed so that other components can be worked on.

Pull back the ribbons and put the battery near the bottom of the Kurio.

The motherboard is now removed so that other components can be worked on.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 11 other contributors

                    Eric Rice

Member since: 04/14/2014

913 Reputation

                                      3 Guides authored                  



                       Badges:
                       20







                                                        +17 more badges

Team

                       Cal Poly, Team 12-36, Maness Spring 2014                        

                                                  Member of Cal Poly, Team 12-36, Maness Spring 2014 



                    CPSU-MANESS-S14S12G36                     


                                            4 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team