Difficulty
Moderate
Steps
7
Time Required
30 minutes
Sections
2
- Back Cover
- 4 steps
- Battery
- 3 steps
Flags
3
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
BackKurio 10S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Turn the device over and place it with the screen down on a flat surface that is clean so the screen does not get scratched.
Turn the device over and place it with the screen down on a flat surface that is clean so the screen does not get scratched.
1024
Step 2
- Locate the four screws, two on each side.
- Using the philips head screwdriver, carefully remove each screw and keep them together in a safe location.
Locate the four screws, two on each side.
Using the philips head screwdriver, carefully remove each screw and keep them together in a safe location.
Step 3
- Once all screws are removed, use a spudger to get under a corner and unclip the hooks.
- Once the spudger is under the cover, slide it all the way around the device, pushing lightly into the device making sure it stays under the cover until all the clips are removed.
- The back cover is difficult to remove, so do not be afraid of using some force once all of the clips have been removed.
Once all screws are removed, use a spudger to get under a corner and unclip the hooks.
Once the spudger is under the cover, slide it all the way around the device, pushing lightly into the device making sure it stays under the cover until all the clips are removed.
The back cover is difficult to remove, so do not be afraid of using some force once all of the clips have been removed.
Step 4
- The back cover should then be able to easily be removed from the device and you should see the battery and other internal components.
The back cover should then be able to easily be removed from the device and you should see the battery and other internal components.
Step 5
Battery
- Remove the electrical tape surrounding the battery.
- Beware of wires under the electrical tape and around the battery that may be fragile.
Remove the electrical tape surrounding the battery.
Beware of wires under the electrical tape and around the battery that may be fragile.
Step 6
- Once the electrical tape is removed there should be a metal bar across the battery.
- Using a philips head screwdriver, remove the screws on both ends and take of the metal bar.
Once the electrical tape is removed there should be a metal bar across the battery.
Using a philips head screwdriver, remove the screws on both ends and take of the metal bar.
Step 7
- Locate the red and black wire connections where the battery is connected to the motherboard.
- Now remove the red and black wires by soldering the ends of the wires off where they connect to the motherboard.
- Soldering irons run hot, and when removing solder from the board make the components hot, so take care when using one.
Locate the red and black wire connections where the battery is connected to the motherboard.
Now remove the red and black wires by soldering the ends of the wires off where they connect to the motherboard.
Soldering irons run hot, and when removing solder from the board make the components hot, so take care when using one.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Timothy Kramer
Member since: 03/27/2015
325 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
UMass Dartmouth, Team 1-6, Shastany Spring 2015
Member of UMass Dartmouth, Team 1-6, Shastany Spring 2015
UMASSD-SHASTANY-S15S1G6
4 Members
8 Guides authored
