Difficulty
Moderate
Steps
15
Time Required
35 minutes
Sections
1
- KRUPS Milk Foamer Type XL2000 Disassembly
- 15 steps
Flags
0
BackKRUPS Milk Foamer Type XL2000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
KRUPS Milk Foamer Type XL2000 Disassembly
- Take off the plexiglass top.
- Remove the white milk spinner from the inside of the foamer.
Take off the plexiglass top.
Remove the white milk spinner from the inside of the foamer.
1024
Step 2
- Remove the 12mm Torx screws (x3) from the bottom of the foamer using a Torx TR10 screwdriver.
Remove the 12mm Torx screws (x3) from the bottom of the foamer using a Torx TR10 screwdriver.
Step 3
- Open the bottom of the foamer.
Open the bottom of the foamer.
Step 4
- Take out the grey and white power cables by pulling out the slide connectors from the base.
Take out the grey and white power cables by pulling out the slide connectors from the base.
Step 5
- Remove the 16mm Torx screw in the middle of the base using a Torx TR20 screwdriver.
- Take off the black bottom from the main body.
Remove the 16mm Torx screw in the middle of the base using a Torx TR20 screwdriver.
Take off the black bottom from the main body.
Step 6
- Grab the power connector in the centre of the black bottom with a monkey wrench.
- Twist the connector clockwise to remove the center power socket.
Grab the power connector in the centre of the black bottom with a monkey wrench.
Twist the connector clockwise to remove the center power socket.
Step 7
- Remove the electromotor-plug using tweezers.
- Make sure to squeeze the small tab on the side of the plug to release it easily.
Remove the electromotor-plug using tweezers.
Make sure to squeeze the small tab on the side of the plug to release it easily.
Step 8
- Remove the electromotor by hand.
Remove the electromotor by hand.
Step 9
- Remove the rubber housing from the electromotor.
- Remove the small rubber cap from the other end of the electromotor.
Remove the rubber housing from the electromotor.
Remove the small rubber cap from the other end of the electromotor.
Step 10
- Press on the two white clips to release the button case.
- Push one side out first to make it easier.
Press on the two white clips to release the button case.
Push one side out first to make it easier.
Step 11
- Pull out the green ribbon cable through the rubber cover.
Pull out the green ribbon cable through the rubber cover.
Step 12
- Pull off the rubber button caps from the button case.
Pull off the rubber button caps from the button case.
Step 13
- Using tweezers, pull off the rubber cover from the base.
- Slide one side of the tweezers under the rubber to get a grip.
Using tweezers, pull off the rubber cover from the base.
Slide one side of the tweezers under the rubber to get a grip.
Step 14
- Using your thumbs, push off the bottom plastic cover from the body.
- Make sure to push and rotate frequently. Pushing on multiple points around the edge of the part allows it to come off easier and without breaking.
- Due to this part being glued in, it takes some force to take it off.
Using your thumbs, push off the bottom plastic cover from the body.
Make sure to push and rotate frequently. Pushing on multiple points around the edge of the part allows it to come off easier and without breaking.
Due to this part being glued in, it takes some force to take it off.
Step 15
- The product is now fully disassembled.
The product is now fully disassembled.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Joost Dommisse
Member since: 03/07/2018
265 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Delft University of Technology, Team S1-G1, Flipsen Winter 2018
Member of Delft University of Technology, Team S1-G1, Flipsen Winter 2018
TUD-FLIPSEN-W18S1G1
4 Members
1 Guide authored
