Kodak Pixpro Az251 Shutter Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Batteries
3 steps
Back Cover
4 steps
LCD Screen
4 steps
Shutter Button
8 steps

Flags

BackKodak PixPro AZ251
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Batteries

Slide switch to open lock position.

Slide switch to open lock position.

1024

Step 2

Press down on the battery cover and slide outwards to open.

Press down on the battery cover and slide outwards to open.

Step 3

Remove the batteries.

Remove the batteries.

Step 4

              Back Cover

Remove a total of four 5mm JIS #000 screws from around the camera:
Two screws from the right side.
Two screws from the left side.

Remove a total of four 5mm JIS #000 screws from around the camera:

Two screws from the right side.

Two screws from the left side.

Step 5

Remove the single 5mm Phillips #00 screw from the bottom.

Remove the single 5mm Phillips #00 screw from the bottom.

Step 6

Open the flash module.
Remove the two 6mm JIS #00 screws found inside of the flash housing.

Open the flash module.

Remove the two 6mm JIS #00 screws found inside of the flash housing.

Step 7

Use a plastic opening tool to pry apart both halves of the camera.
Remove the back panel.

Use a plastic opening tool to pry apart both halves of the camera.

Remove the back panel.

Step 8

              LCD Screen

Remove these three JIS #000 screws from the control board:
5mm screw.
4mm screw.
2mm screw.

Remove these three JIS #000 screws from the control board:

5mm screw.

4mm screw.

2mm screw.

Step 9

Pull the small metal switch plate to the side.

Pull the small metal switch plate to the side.

Step 10

Pry the LCD screen out of the metal housing plate with a plastic opening tool.

Pry the LCD screen out of the metal housing plate with a plastic opening tool.

Step 11

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.
Pull the orange cable out of the socket.

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Pull the orange cable out of the socket.

Step 12

              Shutter Button

Remove one 4mm JIS #000 screw from the top of the camera.

Remove one 4mm JIS #000 screw from the top of the camera.

Step 13

Using tweezers, disconnect the orange cable connection at the top of the motherboard.

Using tweezers, disconnect the orange cable connection at the top of the motherboard.

Step 14

Pull the mode dial up and off of the camera.
Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.

Pull the mode dial up and off of the camera.

Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.

Step 15

Turn camera upside down.
Remove the six 2mm JIS #000 screws from the metal base of the shutter button.

Turn camera upside down.

Remove the six 2mm JIS #000 screws from the metal base of the shutter button.

Step 16

Remove the metal base and ribbon cables.

Remove the metal base and ribbon cables.

Step 17

While holding the shutter button in place, remove the two 4mm JIS #000 screws from the base.

While holding the shutter button in place, remove the two 4mm JIS #000 screws from the base.

Step 18

Remove the plastic base of the shutter button using tweezers by pulling it straight upward.

Remove the plastic base of the shutter button using tweezers by pulling it straight upward.

Step 19

Remove the shutter button by pulling it out from the bottom side of the top cover.

Remove the shutter button by pulling it out from the bottom side of the top cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Rachel Llewellyn

Member since: 02/22/2018

509 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team S1-G1, Cagle Spring 2018                        

                                                  Member of USF Tampa, Team S1-G1, Cagle Spring 2018 



                    USFT-CAGLE-S18S1G1                     


                                            4 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team