Difficulty

Moderate

Steps

17

Time Required

                          30 minutes

Sections

4

  • Batteries
  • 3 steps
  • Back Cover
  • 4 steps
  • LCD Screen
  • 4 steps
  • Mode Dial
  • 6 steps

Flags

0

  • BackKodak PixPro AZ251

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Batteries
  • Slide switch to open lock position.

Slide switch to open lock position.

1024

Step 2

  • Press down on the battery cover and slide outwards to open.

Press down on the battery cover and slide outwards to open.

Step 3

  • Remove the batteries.

Remove the batteries.

Step 4

              Back Cover
  • Remove a total of four 5mm JIS #000 screws from around the camera:
  • Two screws from the right side.
  • Two screws from the left side.

Remove a total of four 5mm JIS #000 screws from around the camera:

Two screws from the right side.

Two screws from the left side.

Step 5

  • Remove the single 5mm Phillips #00 screw from the bottom.

Remove the single 5mm Phillips #00 screw from the bottom.

Step 6

  • Open the flash module.
  • Remove the two 6mm JIS #00 screws found inside of the flash housing.

Open the flash module.

Remove the two 6mm JIS #00 screws found inside of the flash housing.

Step 7

  • Use a plastic opening tool to pry apart both halves of the camera.
  • Remove the back panel.

Use a plastic opening tool to pry apart both halves of the camera.

Remove the back panel.

Step 8

              LCD Screen
  • Remove these three JIS #000 screws from the control board:
  • 5mm screw.
  • 4mm screw.
  • 2mm screw.

Remove these three JIS #000 screws from the control board:

5mm screw.

4mm screw.

2mm screw.

Step 9

  • Pull the small metal switch plate to the side.

Pull the small metal switch plate to the side.

Step 10

  • Pry the LCD screen out of the metal housing plate with a plastic opening tool.

Pry the LCD screen out of the metal housing plate with a plastic opening tool.

Step 11

  • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.
  • Pull the orange cable out of the socket.

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Pull the orange cable out of the socket.

Step 12

              Mode Dial
  • Remove one 4-mm screw using a J000 screwdriver from the top of the camera, near the mode dial.

Remove one 4-mm screw using a J000 screwdriver from the top of the camera, near the mode dial.

Step 13

  • Using the tweezers, disconnect the orange cable connection at the top of the motherboard near the mode dial.

Using the tweezers, disconnect the orange cable connection at the top of the motherboard near the mode dial.

Step 14

  • Pull the top side cover up.
  • Rotate the top side cover to the right.
  • Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.

Pull the top side cover up.

Rotate the top side cover to the right.

Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.

Step 15

  • Turn the camera upside down.
  • Remove two 2mm JIS #000 screws from the metal base of the mode dial.

Turn the camera upside down.

Remove two 2mm JIS #000 screws from the metal base of the mode dial.

Step 16

  • Lift the metal base and remove the 4mm JIS #000 screw from the center of the mode dial.

Lift the metal base and remove the 4mm JIS #000 screw from the center of the mode dial.

Step 17

  • The mode dial should now be loose and can be easily removed from the top side cover.
  • Turn the mode dial upside down to remove the metal part inside.

The mode dial should now be loose and can be easily removed from the top side cover.

Turn the mode dial upside down to remove the metal part inside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Rachel Llewellyn

Member since: 02/22/2018

509 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team S1-G1, Cagle Spring 2018                        

                                                  Member of USF Tampa, Team S1-G1, Cagle Spring 2018 



                    USFT-CAGLE-S18S1G1                     


                                            4 Members                     


                                            7 Guides authored