Difficulty
Moderate
Steps
13
Time Required
15 minutes
Sections
4
- Battery
- 2 steps
- Lens Cover
- 5 steps
- Back Cover
- 3 steps
- LCD Screen
- 3 steps
Flags
0
BackKodak EasyShare Z740
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Slide the door on the bottom of the camera in the direction of the open symbol with your finger.
- Release and the door will pop open.
Slide the door on the bottom of the camera in the direction of the open symbol with your finger.
Release and the door will pop open.
1024
Step 2
- Slide the battery out.
Slide the battery out.
Step 3
Lens Cover
- Remove lens cover from the camera by squeezing the protruding button on each side of the cover and pulling.
Remove lens cover from the camera by squeezing the protruding button on each side of the cover and pulling.
Step 4
- Pull the lens cover string toward the ground so that the loop underneath the metal slab is on top of the cover string.
- Push up so that the string starts to come out of the top of the loop.
- Grab the string from above the loop and pull.
Pull the lens cover string toward the ground so that the loop underneath the metal slab is on top of the cover string.
Push up so that the string starts to come out of the top of the loop.
Grab the string from above the loop and pull.
Step 5
- Feed the string on top into the metal slab while pulling the loop toward you until the plastic piece stops you from pulling any further.
Feed the string on top into the metal slab while pulling the loop toward you until the plastic piece stops you from pulling any further.
Step 6
- Separate the two pieces of the loop and pull the lens cover up in between them.
Separate the two pieces of the loop and pull the lens cover up in between them.
Step 7
- Pull the lens cover and the sting will come out of the metal slab.
Pull the lens cover and the sting will come out of the metal slab.
Step 8
Back Cover
- Place lens cover back on the lens to prevent scratches or debris but leave string detached.
- Remove a total of six 3.968mm Phillips #00 screws. Two each from the left side, bottom, and right side.
Place lens cover back on the lens to prevent scratches or debris but leave string detached.
Remove a total of six 3.968mm Phillips #00 screws. Two each from the left side, bottom, and right side.
Step 9
- Pull the back cover away from the front cover.
- You may need to use a plastic opening tool as a wedge if it does not come apart by easily.
Pull the back cover away from the front cover.
You may need to use a plastic opening tool as a wedge if it does not come apart by easily.
Step 10
- Separate the back cover from the front cover.
Separate the back cover from the front cover.
Step 11
LCD Screen
- Flip the LCD screen down.
Flip the LCD screen down.
Step 12
- Locate the two sets of black tabs connecting the flat orange cables to the motherboard.
- Slide the 2 sets of tabs down with a tool or your finger to release the cables.
Locate the two sets of black tabs connecting the flat orange cables to the motherboard.
Slide the 2 sets of tabs down with a tool or your finger to release the cables.
Step 13
- Gently pull the LCD screen down until the orange cables separate from the motherboard.
Gently pull the LCD screen down until the orange cables separate from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Kirsten Price
Member since: 09/17/2014
406 Reputation
6 Guides authored
Badges:
15
+12 more badges
Team
University of Kentucky Louisville, Team 1-4, Mathis Fall 2014
Member of University of Kentucky Louisville, Team 1-4, Mathis Fall 2014
LOUISVILLE-MATHIS-F14S1G4
4 Members
11 Guides authored
