Difficulty
Moderate
Steps
15
Time Required
15 - 20 minutes
Sections
4
- Battery
- 2 steps
- Back Cover
- 6 steps
- Front Cover
- 3 steps
- Shutter Button
- 4 steps
Flags
0
BackKodak Easyshare C813
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.
Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.
1024
Step 2
- Press thumb firmly on battery door and slide it in the direction of the arrow.
- Lift thumb allowing the door to swing open.
Press thumb firmly on battery door and slide it in the direction of the arrow.
Lift thumb allowing the door to swing open.
Step 3
Back Cover
- Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.
Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.
Step 4
- Turn the camera off by firmly pressing the power button located on top of the camera.
Turn the camera off by firmly pressing the power button located on top of the camera.
Step 5
- Locate the 7 screws holding the back cover on.
- Three screws are located on the bottom of the camera.
- Two screws are located on the side shown in the photograph.
- Two final screws are located on the opposite side shown in the photograph.
Locate the 7 screws holding the back cover on.
Three screws are located on the bottom of the camera.
Two screws are located on the side shown in the photograph.
Two final screws are located on the opposite side shown in the photograph.
Step 6
- Remove all 7 screws:
- Hold the camera firmly with one hand so that you can still see a screw.
- Place the Philips 00(Found here)screwdriver into the screw.
- Turn the screwdriver to the left until it is free.
- Repeat for the remaining screws.
Remove all 7 screws:
Hold the camera firmly with one hand so that you can still see a screw.
Place the Philips 00(Found here)screwdriver into the screw.
Turn the screwdriver to the left until it is free.
Repeat for the remaining screws.
Step 7
- Use plastic opening tools to slightly open the side of the case.
- Insert a plastic opening tool and apply pressure to the internal three tabs at the top.
- The first two are near the words “3X Optical Zoom”.
- The third is near the shutter button.
Use plastic opening tools to slightly open the side of the case.
Insert a plastic opening tool and apply pressure to the internal three tabs at the top.
The first two are near the words “3X Optical Zoom”.
The third is near the shutter button.
Step 8
- Gently pull apart the back cover from the rest of the camera.
- Make sure there are no more screws or tabs keeping the cover on.
- Use the plastic opening tool to separate any sides still closely connected.
Gently pull apart the back cover from the rest of the camera.
Make sure there are no more screws or tabs keeping the cover on.
Use the plastic opening tool to separate any sides still closely connected.
Step 9
Front Cover
- Open the battery door.
- Press thumb firmly on battery door and slide it in the direction of the arrow.
- Lift thumb allowing the door to swing open.
Open the battery door.
Step 10
- Use the plastic opening tool to lift the casing around the shutter button.
- Gently remove the front cover from the device.
Use the plastic opening tool to lift the casing around the shutter button.
Gently remove the front cover from the device.
Step 11
- Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.
- To discharge the capacitor follow this guide.
Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.
To discharge the capacitor follow this guide.
Step 12
Shutter Button
- The shutter button is held on to the front cover by three screws
- Hold the shutter button in place
- Use a Philips 00 screwdriver to remove the screws.
- Careful that the power and flash button do not fall off
The shutter button is held on to the front cover by three screws
Hold the shutter button in place
Use a Philips 00 screwdriver to remove the screws.
Careful that the power and flash button do not fall off
Step 13
- Keep the shutter button in place while removing the circular metal plate
- Remove the shutter button by allowing it to fall into your hand
Keep the shutter button in place while removing the circular metal plate
Remove the shutter button by allowing it to fall into your hand
Step 14
- Hold down the shutter button portion of the selector dial
- Press down the red tabs and slowly relieve pressure on the shutter button
- Press down on the center red stick
- Careful not to lose the spring
- Tool shown is Found here
Hold down the shutter button portion of the selector dial
Press down the red tabs and slowly relieve pressure on the shutter button
Press down on the center red stick
Careful not to lose the spring
Tool shown is Found here
Step 15
- If cleaning, remove dirt from button
- When putting back together, the button should be be oriented so that the green automatic mode points towards the power button.
If cleaning, remove dirt from button
When putting back together, the button should be be oriented so that the green automatic mode points towards the power button.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Susan Marano
Member since: 04/15/2010
318 Reputation
7 Guides authored
Badges:
16
+13 more badges
Team
Cal Poly, Team 24-22, Regan Spring 2010
Member of Cal Poly, Team 24-22, Regan Spring 2010
CPSU-REGAN-S10S24G22
4 Members
20 Guides authored
random - Mar 29, 2013
Reply
does anybody know how the pins works on the surface mounted shutter switch button on the PCB? this would be very helpful thanks!
