Kodak Easyshare C813 Battery Door Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Battery
2 steps
Back Cover
6 steps
Front Cover
3 steps
Battery Door
4 steps

Flags

BackKodak Easyshare C813
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.

Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.

1024

Step 2

Press thumb firmly on battery door and slide it in the direction of the arrow.
Lift thumb allowing the door to swing open.

Press thumb firmly on battery door and slide it in the direction of the arrow.

Lift thumb allowing the door to swing open.

Step 3

              Back Cover

Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.

Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.

Step 4

Turn the camera off by firmly pressing the power button located on top of the camera.

Turn the camera off by firmly pressing the power button located on top of the camera.

Step 5

Locate the 7 screws holding the back cover on.
Three screws are located on the bottom of the camera.
Two screws are located on the side shown in the photograph.
Two final screws are located on the opposite side shown in the photograph.

Locate the 7 screws holding the back cover on.

Three screws are located on the bottom of the camera.

Two screws are located on the side shown in the photograph.

Two final screws are located on the opposite side shown in the photograph.

Step 6

Remove all 7 screws:
Hold the camera firmly with one hand so that you can still see a screw.
Place the Philips 00(Found here)screwdriver into the screw.
Turn the screwdriver to the left until it is free.
Repeat for the remaining screws.

Remove all 7 screws:

Hold the camera firmly with one hand so that you can still see a screw.

Place the Philips 00(Found here)screwdriver into the screw.

Turn the screwdriver to the left until it is free.

Repeat for the remaining screws.

Step 7

Use plastic opening tools to slightly open the side of the case.
Insert a plastic opening tool and apply pressure to the internal three tabs at the top.
The first two are near the words “3X Optical Zoom”.
The third is near the shutter button.

Use plastic opening tools to slightly open the side of the case.

Insert a plastic opening tool and apply pressure to the internal three tabs at the top.

The first two are near the words “3X Optical Zoom”.

The third is near the shutter button.

Step 8

Gently pull apart the back cover from the rest of the camera.
Make sure there are no more screws or tabs keeping the cover on.
Use the plastic opening tool to separate any sides still closely connected.

Gently pull apart the back cover from the rest of the camera.

Make sure there are no more screws or tabs keeping the cover on.

Use the plastic opening tool to separate any sides still closely connected.

Step 9

              Front Cover

Open the battery door.
Press thumb firmly on battery door and slide it in the direction of the arrow.
Lift thumb allowing the door to swing open.

Open the battery door.

Step 10

Use the plastic opening tool to lift the casing around the shutter button.
Gently remove the front cover from the device.

Use the plastic opening tool to lift the casing around the shutter button.

Gently remove the front cover from the device.

Step 11

Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.
To discharge the capacitor follow this guide.

Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.

To discharge the capacitor follow this guide.

Step 12

              Battery Door

Open the battery door by pulling in direction of arrow

Open the battery door by pulling in direction of arrow

Step 13

Use grey wedge(Found here) to push metal pin
Use tweezers(Found here)to pull out metal pin

Use grey wedge(Found here) to push metal pin

Use tweezers(Found here)to pull out metal pin

Step 14

The spring is small and easy to lose
Carefully remove battery door and spring

The spring is small and easy to lose

Carefully remove battery door and spring

Step 15

Make spring is in correct orientation when putting back
The spring should hook onto a small hole in the door

Make spring is in correct orientation when putting back

The spring should hook onto a small hole in the door

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 6 other contributors

                    Susan Marano

Member since: 04/15/2010

318 Reputation

                                      7 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       Cal Poly, Team 24-22, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 24-22, Regan Spring 2010 



                    CPSU-REGAN-S10S24G22                     


                                            4 Members                     


                                            20 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team