Featured

Featured Guide

Difficulty

Difficult

Steps

10

Time Required

                          20 minutes

Sections

3

  • Batteries
  • 2 steps
  • Outer Case
  • 2 steps
  • LCD
  • 6 steps

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackKodak EasyShare C713

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Batteries
  • Use your finger tip to slide battery cover door away from the center of the camera.
  • The battery door should spring open.
  • If this does not happen, gently open the door lifting from the outer bottom side of the camera.

Use your finger tip to slide battery cover door away from the center of the camera.

The battery door should spring open.

If this does not happen, gently open the door lifting from the outer bottom side of the camera.

1024

Step 2

  • Remove the old batteries.

Remove the old batteries.

Step 3

              Outer Case
  • Remove the seven screws from the outer case with a Phillips #00.
  • All screws are 4.45mm.
  • There are 2 screws on the port side.
  • There are 2 screws on starboard side.
  • There are 3 screws on the bottom.

Remove the seven screws from the outer case with a Phillips #00.

All screws are 4.45mm.

There are 2 screws on the port side.

There are 2 screws on starboard side.

There are 3 screws on the bottom.

Step 4

  • Make sure the battery cap is “up”.
  • Pull the outer case off with your hands.

Make sure the battery cap is “up”.

Pull the outer case off with your hands.

Step 5

              LCD
  • The LCD screen is hinged at the bottom.
  • Put your thumb in the upper right corner of the LCD screen.
  • Pull the LCD screen out of its outer case with your thumb.

The LCD screen is hinged at the bottom.

Put your thumb in the upper right corner of the LCD screen.

Pull the LCD screen out of its outer case with your thumb.

Step 6

  • Remove the screw underneath LCD screen with the Phillips #00. The screw measures 4.1mm in length.

Remove the screw underneath LCD screen with the Phillips #00. The screw measures 4.1mm in length.

Step 7

  • Desolder the two points.
  • One on the port side.
  • One on the bottom.

Desolder the two points.

One on the port side.

One on the bottom.

Step 8

  • After desoldering the LCD casing, just use your fingers to carefully remove it.

After desoldering the LCD casing, just use your fingers to carefully remove it.

Step 9

  • Flip up the black tab on the bottom of the LCD screen with a fingertip.

Flip up the black tab on the bottom of the LCD screen with a fingertip.

Step 10

  • Remove the LCD ribbon cable from inside the black tab.

Remove the LCD ribbon cable from inside the black tab.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 6 other contributors 


                    Taggart Ashby

Member since: 04/15/2010

345 Reputation

                                      4 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 26-19, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 26-19, Regan Spring 2010 



                    CPSU-REGAN-S10S26G19                     


                                            4 Members                     


                                            14 Guides authored

anthoxman - Jan 22, 2016

Reply

Thank you… i fixed my old camera lcd.