Kitchenaid Professional 600 Drive Motor Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

3

• Top Cover
• 3 steps
• Speed Selector
• 3 steps
• Drive Motor
• 2 steps

Flags

0

• BackKitchenAid Professional 600

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Top Cover               

• Take out the screw which holds on the silver band using a Phillips #2 screwdriver.
• Remove the silver band.

Take out the screw which holds on the silver band using a Phillips #2 screwdriver.

Remove the silver band.

1024

Step 2

• Remove the four Phillips #2 screws located around the mixer where the band was removed.
• This picture only shows two of the screw that you need to remove. The other two are on the exact opposite side of the mixer.

Remove the four Phillips #2 screws located around the mixer where the band was removed.

This picture only shows two of the screw that you need to remove. The other two are on the exact opposite side of the mixer.

Step 3

• Remove the top of the mixer to reveal the inner parts.
• The top should lift off, but may not if it is stuck. A sharp strike from the back with the hand may unstick it. It will slide forward about a 3/8 of an inch. Push it back again from the front and it should be free enough to lift.

Remove the top of the mixer to reveal the inner parts.

The top should lift off, but may not if it is stuck. A sharp strike from the back with the hand may unstick it. It will slide forward about a 3/8 of an inch. Push it back again from the front and it should be free enough to lift.

Step 4

              Speed Selector               

• Locate the selector switch.
• Remove the two Phillips #2 screws holding the selector switch in place.

Locate the selector switch.

Remove the two Phillips #2 screws holding the selector switch in place.

Step 5

• Unplug the cords attached the drive motor to the switch.
• We suggest numbering them left from right so they are reattached to the replacement part in the right order.

Unplug the cords attached the drive motor to the switch.

We suggest numbering them left from right so they are reattached to the replacement part in the right order.

Step 6

• Pull out the Selector Switch.

Pull out the Selector Switch.

Step 7

              Drive Motor               

• Remove the two Phillips #2 screws holding the motor in place, located near the fan at the back of the motor.
• The picture only shows one of the screws. The other screw is located on the exact opposite side of the motor.

Remove the two Phillips #2 screws holding the motor in place, located near the fan at the back of the motor.

The picture only shows one of the screws. The other screw is located on the exact opposite side of the motor.

Step 8

• Pull upward to remove the motor.

Pull upward to remove the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Tallon Dotinga                     

Member since: 04/11/2016

459 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Cal Poly, Team 25-4, Maness Spring 2016                        

                                                  Member of Cal Poly, Team 25-4, Maness Spring 2016 



                    CPSU-MANESS-S16S25G4                     


                                            4 Members                     


                                            14 Guides authored                     

Barclay Berger - Sep 6, 2017

Reply

anyone know where I can get the hall effect sensor receiver that is on the motor shaft? Somehow it’s missing?

wa1shm - Dec 14, 2019

Reply

is there not a fusible link in series with the drive motor?

hyalmar planta - Apr 9, 2020

Reply

I accidentally pluged my 110v mixer to 220v. Now, what are the possible parts that i need to change? How can i check if the motor is busted?