Difficulty
Moderate
Steps
15
Time Required
30 minutes
Sections
1
- Electronic Control Board
- 15 steps
Flags
0
BackDishwasher
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The control board controls all of the dishwasher’s functions, such as filling, washing, drying, and draining. Symptoms that match your issue can be diagnosed by viewing these Dishwasher Repairs. During the time it takes to replace the dishwasher control board, remind your family not to run the dishwasher for about 30 minutes.
Before replacing the electronic control board, make sure the power/electricity is off. Disconnect the dishwasher from any external power source before starting the process and turn off the dishwasher completely.
What you need
Step 1
Electronic Control Board
- Unplug the dishwasher or shut off the house circuit breaker for the dishwasher.
- To verify that power is disconnected, make sure that the control panel doesn’t light up when you press a control button or the power button.
Unplug the dishwasher or shut off the house circuit breaker for the dishwasher.
To verify that power is disconnected, make sure that the control panel doesn’t light up when you press a control button or the power button.
1024
Step 2
- Open the dishwasher door.
Open the dishwasher door.
Step 3
- Remove the four screws from each side of the dishwasher door (eight screws total).
- Removing the three screws from each side of the dishwasher (six screws total).
- Support the outer door panel with one hand as you remove the final two screws at the top of the dishwasher door.
- There are total of sixteen (16) screws.
Remove the four screws from each side of the dishwasher door (eight screws total).
Removing the three screws from each side of the dishwasher (six screws total).
Support the outer door panel with one hand as you remove the final two screws at the top of the dishwasher door.
There are total of sixteen (16) screws.
Step 4
- Use your hands to pull off the outer door panel with the control panel.
Use your hands to pull off the outer door panel with the control panel.
Step 5
- Disconnect the two white outer wires by pulling them out.
- The two white connectors have the same size and are close together.
- Use one hand to hold the control panel while disconnecting the electrical connections from the old board.
Disconnect the two white outer wires by pulling them out.
The two white connectors have the same size and are close together.
Use one hand to hold the control panel while disconnecting the electrical connections from the old board.
Step 6
- Remove the white rectangular connector that has six colored wires connected to it.
Remove the white rectangular connector that has six colored wires connected to it.
Step 7
- Use one hand to hold the control panel while detaching the black connector.
- The black connector is the main connector to the control board.
Use one hand to hold the control panel while detaching the black connector.
The black connector is the main connector to the control board.
Step 8
- Detach the white and gray ribbon cable attached to the black connector.
Detach the white and gray ribbon cable attached to the black connector.
Step 9
- Use your hands to pull the electronic control board out the mounting slots.
Use your hands to pull the electronic control board out the mounting slots.
Step 10
- Push the new electronic control board into the mounting slots.
- Slide it to the right to engage the locking tab until you hear a click.
Push the new electronic control board into the mounting slots.
Slide it to the right to engage the locking tab until you hear a click.
Step 11
- Reconnect the black connector wires to the new electronic control board.
Reconnect the black connector wires to the new electronic control board.
Step 12
- Reconnect the white rectangular connector with six wires to the new electronic control board.
Reconnect the white rectangular connector with six wires to the new electronic control board.
Step 13
- Reconnect the two white outer connector wires to the new electronic control board.
Reconnect the two white outer connector wires to the new electronic control board.
Step 14
- Reinstall the outer door panel and control panel on the inner door panel and reattach the user interface control wire harness.
- Reinstall the sixteen mounting screws.
Reinstall the outer door panel and control panel on the inner door panel and reattach the user interface control wire harness.
Reinstall the sixteen mounting screws.
Step 15
- Connect the dishwasher and reset the circuit breaker for your house to restore electricity.
- To verify that power is connected, make sure that the control panel does light up when you press a control button or the power button.
Connect the dishwasher and reset the circuit breaker for your house to restore electricity.
To verify that power is connected, make sure that the control panel does light up when you press a control button or the power button.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Thuan Trang
Member since: 01/13/2022
345 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
York University, Team S-29, Woodhouse Winter 2022
Member of York University, Team S-29, Woodhouse Winter 2022
YORK-WOODHOUSE-W22SSG29
1 Member
2 Guides authored
KO SAMUEL TAK SHUN - Sep 17, 2022
Reply
Excellent illustration!!!
khaliddabnoun - Jan 11, 2023
Reply
عمل فنى رائع وجميل وبدقة متناهية
عمل فنى جميل ورائع وبدقة متناهية
