Difficulty
Moderate
Steps
9
Time Required
10 minutes
Sections
3
- Back Panel
- 2 steps
- Fan
- 3 steps
- Motor
- 4 steps
Flags
0
BackKitchenAid KSB5CR Blender
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing the Back Panel Part 1
- Remove the glass container and place the blender upside down on a solid surface.
- Remove the four rubber feet using the needle nose pliers.
- Remove the four #7.5 Phillips 25mm screws that were located underneath the rubber feet using the Phillips #2 screwdriver.
Remove the glass container and place the blender upside down on a solid surface.
Remove the four rubber feet using the needle nose pliers.
Remove the four #7.5 Phillips 25mm screws that were located underneath the rubber feet using the Phillips #2 screwdriver.
1024
Step 2
Removing the Back Panel Part 2
- Lift the back panel up, sliding it along the power cord.
Lift the back panel up, sliding it along the power cord.
Step 3
Removing the Fan Chassis Part 1
- Remove the two #5 Phillips 95 mm machine screws using the Phillips #2 screwdriver.
- Remove the rubber O-ring by lifting it up.
- Remove the ribbon cable from the chassis by lifting it up.
Remove the two #5 Phillips 95 mm machine screws using the Phillips #2 screwdriver.
Remove the rubber O-ring by lifting it up.
Remove the ribbon cable from the chassis by lifting it up.
Step 4
Removing the Fan Chassis Part 2
- Unhook the white wire that is looped around the peg by pulling it out of the clip.
- Repeat this process with the red wire on the other side of the chassis.
- Remove the end cap using the 8" needle nose pliers.
- Pull up the fan chassis.
Unhook the white wire that is looped around the peg by pulling it out of the clip.
Repeat this process with the red wire on the other side of the chassis.
Remove the end cap using the 8" needle nose pliers.
Pull up the fan chassis.
Step 5
Removing the Fan
- Remove the fan by lifting it upwards.
- This step is difficult and requires force. Use of both hands is recommended.
Remove the fan by lifting it upwards.
This step is difficult and requires force. Use of both hands is recommended.
Step 6
Removing the Metal Cap
- Use the needle nose pliers to turn the coupling clockwise to loosen it.
Use the needle nose pliers to turn the coupling clockwise to loosen it.
Step 7
Removing the Screws
- Rotate the blender 90 degrees clockwise.
- Remove the two #8 Phillips 12 mm screws using the Phillips #2 screwdriver.
Rotate the blender 90 degrees clockwise.
Remove the two #8 Phillips 12 mm screws using the Phillips #2 screwdriver.
Step 8
Detatching the Wire
- Slide the knife in the metal loop holding the insulation before the white copper wire, and wiggle the knife back and forth until it loosens.
- Pull the wire out from the metal loop that you loosened.
Slide the knife in the metal loop holding the insulation before the white copper wire, and wiggle the knife back and forth until it loosens.
Pull the wire out from the metal loop that you loosened.
Step 9
Removing the Motor
- Lift the motor up out of the chassis.
Lift the motor up out of the chassis.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Cameron Geehr
Member since: 09/28/2014
721 Reputation
6 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team 12-5, Forte Fall 2014
Member of Cal Poly, Team 12-5, Forte Fall 2014
CPSU-FORTE-F14S12G5
5 Members
6 Guides authored
