Kindle 7Th Generation Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes - 1 hour

Sections

Front Panel
2 steps
Back Panel
2 steps
Motherboard
6 steps
Screen
4 steps

Flags

BackKindle 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front Panel

Power off your Kindle before beginning disassembly.
At each corner, use the blue plastic opening tool to unhook and separate the front panel from the adhesive.
Run the tool along the seams to pry open the front panel.

Power off your Kindle before beginning disassembly.

At each corner, use the blue plastic opening tool to unhook and separate the front panel from the adhesive.

Run the tool along the seams to pry open the front panel.

1024

Step 2

Peel the front panel off to remove it from the Kindle.
If this is the first time the front panel has been removed, the adhesive may require a significant amount of force to undo.
To prevent damaging the front panel, peel the panel from the corners towards the middle of the Kindle.
When reassembling your device, if you are replacing the front panel, additional adhesive may be required.

Peel the front panel off to remove it from the Kindle.

If this is the first time the front panel has been removed, the adhesive may require a significant amount of force to undo.

To prevent damaging the front panel, peel the panel from the corners towards the middle of the Kindle.

When reassembling your device, if you are replacing the front panel, additional adhesive may be required.

Step 3

              Back Panel

Remove the ten 5.0 mm T5 Torx screws.
A magnetized screw mat can help you keep track of your screws.

Remove the ten 5.0 mm T5 Torx screws.

A magnetized screw mat can help you keep track of your screws.

Step 4

Working evenly along the corners and edges, separate the internal contents from the back panel.
There are many clips securing the screen to the back panel. Force will be required to remove the back, but you should never feel that the Kindle may break.

Working evenly along the corners and edges, separate the internal contents from the back panel.

There are many clips securing the screen to the back panel. Force will be required to remove the back, but you should never feel that the Kindle may break.

Step 5

              Motherboard

Flip the screen over to face the motherboard and battery pack.
Use the blunted precision tweezers to gently unclip and detach the cable connecting the battery pack and motherboard.

Flip the screen over to face the motherboard and battery pack.

Use the blunted precision tweezers to gently unclip and detach the cable connecting the battery pack and motherboard.

Step 6

Use the tip of the spudger to flip up the small retaining flap on the copper colored zero insertion force (ZIF) connector.
Make sure to flip up the flap and not the connection itself.
Pull the cable from the connector.
No force is required to do this, as the name, ZIF, implies.

Use the tip of the spudger to flip up the small retaining flap on the copper colored zero insertion force (ZIF) connector.

Make sure to flip up the flap and not the connection itself.

Pull the cable from the connector.

No force is required to do this, as the name, ZIF, implies.

Step 7

Similar to the previous step, flip up the retaining flap on the white cable connector.
Pull the white cable from the connection.
During reassembly, make sure the retaining flaps for both the white and copper colored cable connections are secured. As these are zero insertion force connections, the cables could potentially slide out if this is not done.

Similar to the previous step, flip up the retaining flap on the white cable connector.

Pull the white cable from the connection.

During reassembly, make sure the retaining flaps for both the white and copper colored cable connections are secured. As these are zero insertion force connections, the cables could potentially slide out if this is not done.

Step 8

Disconnect the touch digitiser bridge cable by using your Spudger to lift up the white tabs on both connectors.
Use tweezers to pull out the cable.
The touch digitiser bridge cable is the one connecting between these two connectors.

Disconnect the touch digitiser bridge cable by using your Spudger to lift up the white tabs on both connectors.

Use tweezers to pull out the cable.

The touch digitiser bridge cable is the one connecting between these two connectors.

Step 9

Use the T5 Torx screwdriver to remove the eight 3.0 mm Phillips Head screws.
Some screws have washers associated with them. It is important to keep track of the washers and remember which thread they came from.

Use the T5 Torx screwdriver to remove the eight 3.0 mm Phillips Head screws.

Some screws have washers associated with them. It is important to keep track of the washers and remember which thread they came from.

Step 10

Remove the motherboard.

Remove the motherboard.

Step 11

              Screen

Remove the two 2.5 mm Phillips Head screws using the T5 Torx screwdriver.

Remove the two 2.5 mm Phillips Head screws using the T5 Torx screwdriver.

Step 12

Use the plastic opening tool to pry the battery from the back side of the screen.
The battery has excessive adhesive so this may take some extra effort.

Use the plastic opening tool to pry the battery from the back side of the screen.

The battery has excessive adhesive so this may take some extra effort.

Step 13

Run the plastic opening tool around the edge to separate the bezel from the adhesive.

Run the plastic opening tool around the edge to separate the bezel from the adhesive.

Step 14

Remove the bezel from the screen.
Use care, the bezel and circuit board are flimsy and the adhesive is strong.

Remove the bezel from the screen.

Use care, the bezel and circuit board are flimsy and the adhesive is strong.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 2 other contributors

                    Mitchell

Member since: 01/30/2015

755 Reputation

                                      1 Guide authored                  



                       Badges:
                       17







                                                        +14 more badges

Team

                       Cal Poly, Team 6-28, Amido Winter 2015                        

                                                  Member of Cal Poly, Team 6-28, Amido Winter 2015 



                    CPSU-AMIDO-W15S6G28                     


                                            4 Members                     


                                            12 Guides authored

Geraldo Kuster - May 30, 2016

I Need this Screen for my kindle, where find to buy.

Galen Robison - Jan 22, 2017

yassine el fakir - May 31, 2018

Hi, I have a big problem with my kindle 7th genration, the screen is frozen, I tried the root by pushing start buton for 40 sec and more, nothing, even if I took apart every peace of the tablaet ( main board batery…) it still frozen !!!! how can I fix it? thank you

Victor Leija - Feb 5, 2019

i just let mine sit for a few months i didn’t even turn it on after a few months i plugged it in then turned it on and it worked

Marts Liena - Mar 28, 2021

Introduction#

What you need#

Team#

Introduction

What you need

Team