Difficulty
Moderate
Steps
9
Time Required
10 - 20 minutes
Sections
2
- Top Needle
- 3 steps
- Handle
- 6 steps
Flags
0
BackKeurig K10 Mini Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Needle
- Remove two 9 mm Phillips #1 screws.
- Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.
- The screws are located on the top of where the K-Cup would be.
Remove two 9 mm Phillips #1 screws.
Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.
The screws are located on the top of where the K-Cup would be.
1024
Step 2
- Once you remove the screws, the top cover should come out.
- You will then want to remove these screws which are the same size.
- The needle is sharp, so be careful.
Once you remove the screws, the top cover should come out.
You will then want to remove these screws which are the same size.
The needle is sharp, so be careful.
Step 3
- Once you get those removed, you are going to want to pull on the hose until it pops off.
- Once the hose comes off, the needle will fall out by itself.
- Be careful when picking up the needle as the needle is sharp.
Once you get those removed, you are going to want to pull on the hose until it pops off.
Once the hose comes off, the needle will fall out by itself.
Be careful when picking up the needle as the needle is sharp.
Step 4
Handle
- Remove the two Phillips #1 screws.
- The top needle is intact and there, so be careful when in this area.
Remove the two Phillips #1 screws.
The top needle is intact and there, so be careful when in this area.
Step 5
- Next, after the removal of the hose on the top by simply pulling it off, remove the following four Phillips #1 screws.
Next, after the removal of the hose on the top by simply pulling it off, remove the following four Phillips #1 screws.
Step 6
- Once you take off the screws, this part of the handle will come off.
Once you take off the screws, this part of the handle will come off.
Step 7
- To pull this part off, pull inwards with the these tabs located on both sides of the handle assembly.
To pull this part off, pull inwards with the these tabs located on both sides of the handle assembly.
Step 8
- Next, remove these two Phillips #1 screws to allow the release of the actual handle from the frame.
- For the O rings, we used the plastic prying tools. Just keep in mind that you might want to hold one side of the O ring down while trying to pry off the other side with the other.
- Once you get the O rings on both sides out, you can pull the handle by pulling on each side.
Next, remove these two Phillips #1 screws to allow the release of the actual handle from the frame.
For the O rings, we used the plastic prying tools. Just keep in mind that you might want to hold one side of the O ring down while trying to pry off the other side with the other.
Once you get the O rings on both sides out, you can pull the handle by pulling on each side.
Step 9
- Once you pull both sides, the handle will come off as shown.
Once you pull both sides, the handle will come off as shown.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Roberto Maldonado
Member since: 02/04/2016
395 Reputation
1 Guide authored
Badges:
14
+11 more badges
Team
iFixit, Team 1-1, Weber Winter 2016
Member of iFixit, Team 1-1, Weber Winter 2016
FIX-WEBER-W16S1G1
4 Members
29 Guides authored
