Difficulty
Moderate
Steps
8
Time Required
15 - 20 minutes
Sections
1
- LCD Screen
- 8 steps
Flags
0
BackKeurig 2.0-400
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
LCD Screen
- Open the K-Cup Chamber Housing Lid by lifting up the silver handle below the LCD screen.
- This is the part of the brewer you open to place a K-Cup inside.
Open the K-Cup Chamber Housing Lid by lifting up the silver handle below the LCD screen.
This is the part of the brewer you open to place a K-Cup inside.
1024
Step 2
- Place the Keurig on its side.
- Remove the two 140mm screws located on the underside of the Chamber Lid using the Phillips #1 screwdriver.
- Remove the top black housing that surrounds the screen.
Place the Keurig on its side.
Remove the two 140mm screws located on the underside of the Chamber Lid using the Phillips #1 screwdriver.
Remove the top black housing that surrounds the screen.
Step 3
- Using the Phillips #1 screwdriver, remove the two 140mm screws connecting the silver handle to the top of the Keurig.
Using the Phillips #1 screwdriver, remove the two 140mm screws connecting the silver handle to the top of the Keurig.
Step 4
- Pull out the front silver handle from the top of the brewer.
- This will further expose the LCD screen.
Pull out the front silver handle from the top of the brewer.
This will further expose the LCD screen.
Step 5
- Using the metal spudger, pry open the snaps holding the LCD screen panel to the brewer, just enough for the panel to pop loose.
- Warning: These snaps are very delicate and can easily be broken. Practice caution as you perform this step.
Using the metal spudger, pry open the snaps holding the LCD screen panel to the brewer, just enough for the panel to pop loose.
Warning: These snaps are very delicate and can easily be broken. Practice caution as you perform this step.
Step 6
- Remove the top black housing by lifting it up.
- This will expose the frame of the Keurig connecting to the LCD screen.
Remove the top black housing by lifting it up.
This will expose the frame of the Keurig connecting to the LCD screen.
Step 7
- Remove the black latch with the black wire connecting the front end of the panel to the frame.
- The front end of the panel will now be free.
Remove the black latch with the black wire connecting the front end of the panel to the frame.
The front end of the panel will now be free.
Step 8
- On the bottom of the panel, remove the white tab that connects the wires of the circuit board to the LCD screen
- To remove the tab, squeeze in on the sides of it as you pull it out.
- Remove the touch screen panel from your device.
On the bottom of the panel, remove the white tab that connects the wires of the circuit board to the LCD screen
To remove the tab, squeeze in on the sides of it as you pull it out.
Remove the touch screen panel from your device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 6 other contributors
Alec Jamosmos
Member since: 04/22/2018
915 Reputation
5 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S24-G8, Maness Spring 2018
Member of Cal Poly, Team S24-G8, Maness Spring 2018
CPSU-MANESS-S18S24G8
4 Members
5 Guides authored
Christopher Rodriguez - Aug 18, 2018
Reply
Hello Alec,
Thank you for providing this repair guide! Could you kindly provide the screen size and where one might be able to purchase one? It would be greatly appreciated.
Regards.
staci werkmeister - Aug 24, 2018
Reply
Yes love the demo, now where would one find the screen to replace. Keurig states these are no longer available.
DEBORAH A YOCHIM - Nov 16, 2019
Reply
Try eBay. I saw one there.
I saw one on eBay.