Difficulty

Difficult

Steps

14

Time Required

                          2 - 6 hours

Sections

1

  • Planetary set SER1018
  • 14 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackKenwood Chef

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Step 1

              Remove the locking latch knob
  • Remove the button
  • Remove the white sheath

Remove the button

Remove the white sheath

1024

Step 2

              Remove the sun gear
  • Unscrew the hex nut
  • Remove the sun gear straight ahead.
  • Unscrew the Torx screws fixing the bottom of the housing to the machine

Unscrew the hex nut

Remove the sun gear straight ahead.

Unscrew the Torx screws fixing the bottom of the housing to the machine

Step 3

              Bottom of the machine
  • Remove the bottom of the machine
  • The elastic seal can be removed for cleaning
  • Remove the felt pad

Remove the bottom of the machine

The elastic seal can be removed for cleaning

Remove the felt pad

Step 4

              Fast and medium speed outputs
  • Unscrew the screws on each side of the circular discs to remove the circular plastic discs
  • The discs and screws are different, be sure to take note of where they go

Unscrew the screws on each side of the circular discs to remove the circular plastic discs

The discs and screws are different, be sure to take note of where they go

Step 5

              Housing cover
  • Unscrew the three Torx screws
  • Lift the housing cover up and out of the machine.
  • Pay attention to the alignment of the white shock absorber and where it was when you removed the housing. (red mark)

Unscrew the three Torx screws

Lift the housing cover up and out of the machine.

Pay attention to the alignment of the white shock absorber and where it was when you removed the housing. (red mark)

Step 6

              The challenge: loosen the hidden screw
  • It is not necessary to proceed to the next step if the plastic drive wheel has been removed
  • According to “Jens” simply turn the plastic drive wheel in the opposite direction of the watch to remove it, while blocking the housing. “Julien” found a YouTube video that shows how to proceed. Start at 7:25. Big thanks to Jens and Julien.
  • It’s very hard to loosen the Tx20 screw hidden by the plastic drive wheel. Beware of metal burrs that your finger may catch.
  • I did not manage to remove the drive wheel from its axis
  • Whoever takes the risk can make a hole in the wheel. I did not have the courage.
  • I made a special tool -> See next.

It is not necessary to proceed to the next step if the plastic drive wheel has been removed

According to “Jens” simply turn the plastic drive wheel in the opposite direction of the watch to remove it, while blocking the housing. “Julien” found a YouTube video that shows how to proceed. Start at 7:25. Big thanks to Jens and Julien.

It’s very hard to loosen the Tx20 screw hidden by the plastic drive wheel. Beware of metal burrs that your finger may catch.

I did not manage to remove the drive wheel from its axis

Whoever takes the risk can make a hole in the wheel. I did not have the courage.

I made a special tool -> See next.

Step 7

              Special Tool
  • I modified an open end wrench to drive a Tx20 bit
  • A slot has been made to facilitate the reassembly of the screw

I modified an open end wrench to drive a Tx20 bit

A slot has been made to facilitate the reassembly of the screw

Step 8

              Open the housing
  • Remove the guides (red mark). They can be reassembled after closing the housing
  • Remove the seal. I replaced it with silicone similar to what is used in the bathroom.

Remove the guides (red mark). They can be reassembled after closing the housing

Remove the seal. I replaced it with silicone similar to what is used in the bathroom.

Step 9

              Planetary
  • The former one has a cross fromation.
  • The new one has a bayonet tool port. The beater and the whip are in the same position relative to the bowl.
  • The width of the toothed wheel does not seem to have any difference.

The former one has a cross fromation.

The new one has a bayonet tool port. The beater and the whip are in the same position relative to the bowl.

The width of the toothed wheel does not seem to have any difference.

Step 10

              Training axis
  • The former one has a cross patteren

The former one has a cross patteren

Step 11

              Labels
  • Cod. SER1018: Plastic bag containing the three spare parts
  • Planetary label
  • Hex nut: label and price

Cod. SER1018: Plastic bag containing the three spare parts

Planetary label

Hex nut: label and price

Step 12

              Fitting the gears
  • Place each gear on the axis
  • Be sure that the gear teeth line up!

Place each gear on the axis

Be sure that the gear teeth line up!

Step 13

              Crank Case Assembly
  • There is a lot of greasein the case. Spread the grease on the surfaces that need it.
  • Replace the seal. See step 8.
  • Set the machine up with the arm in a horizontal position. The shaft of the will fall if the arm is raised
  • Gently slide the two parts into each other.
  • The screws were loose during disassembly. I fixed them with a drop of screw fixation solution.
  • Reinsert the guides to the original positions

There is a lot of greasein the case. Spread the grease on the surfaces that need it.

Replace the seal. See step 8.

Set the machine up with the arm in a horizontal position. The shaft of the will fall if the arm is raised

Gently slide the two parts into each other.

The screws were loose during disassembly. I fixed them with a drop of screw fixation solution.

Reinsert the guides to the original positions

Step 14

              Hidden screw
  • Screw the hidden screw back in
  • Tighten with the special tool of step 7

Screw the hidden screw back in

Tighten with the special tool of step 7

To reassemble your device, follow these steps in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.                                             


        [deleted] is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

[deleted]

Author

                                      with 2 other contributors 


                    Bruno M

Member since: 02/14/2015

752 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

f g - Apr 10, 2018

Reply

non mais les vieux ustensiles ne sont pas compatible avec le nouvelle axe

Brendan - Jun 1, 2018

Reply

Ce tutoriel est très utile pour démontrer un model similaire (le KM070)

Jeannot la bricole - Dec 18, 2019

Reply

Merci c’est très utile. Pour enlever la vis T20 sous la roue d’entraînement j’ai utilisé une clé torx à angle droit du commerce. Pour la remonter un petit trou de 8 sur le dessus de la roue pour passer la clé sans rien affaiblir. Pour le joint je pense que le silicone n’est pas judicieux car on ne pourra plus le démonter . J’ai opté pour un mastic de plombier genre Gebajoint.

Bruno M - Jun 1, 2020

Reply

Selbe Anleitung in Deutsch: Kenwood Chef Gear Drive SER1018 Replacement

Same tutorial in English: Kenwood Chef Gear Drive SER1018 Replacement

Bernard Frise - Jun 5, 2021

Reply

J’ai pris l’option de percer la grande roue crantée. J’y suis allez doucement et c’est ok pour enlever la vis