Difficulty

Moderate

Steps

10

Time Required

                          1 hour

Sections

1

  • Drive Gear
  • 10 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackKenwood Chef

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Tools
  • Prepare your Tools.

Prepare your Tools.

1024

Step 2

              Open Electronic box
  • Remove five Screens T20 from the bottom and lift the bottom plate up.

Remove five Screens T20 from the bottom and lift the bottom plate up.

Step 3

              Remove electronic box
  • Separate nine cables.
  • Remove all screws from the electronic box.
  • Remove the electronic box.

Separate nine cables.

Remove all screws from the electronic box.

Remove the electronic box.

Step 4

              Loosen the tilt mechanics
  • Tilt the machine head.
  • Remove the security washer from the hinge axle.
  • Remove the axle and the machine stand.

Tilt the machine head.

Remove the security washer from the hinge axle.

Remove the axle and the machine stand.

Step 5

              Spring and design plate
  • Pull the spring out.
  • Remove the screw.
  • Remove the design plate.

Pull the spring out.

Remove the screw.

Remove the design plate.

Step 6

              Remove cover
  • Remove four screws T20.
  • Remove the cover.

Remove four screws T20.

Remove the cover.

Step 7

              Remove top cover
  • Remove two screws T20.
  • Remove the top cover. Note: the cable connecting the top cover and the lower case is very short.
  • Remove the screws from the “Light on/off”-unit and separate it from the top cover.

Remove two screws T20.

Remove the top cover. Note: the cable connecting the top cover and the lower case is very short.

Remove the screws from the “Light on/off”-unit and separate it from the top cover.

Step 8

              Remove motor cover
  • Remove three screws T20 and the washers.
  • Take the cover off.

Remove three screws T20 and the washers.

Take the cover off.

Step 9

              Motor
  • Remove three screws T20 and the plastic washers.

Remove three screws T20 and the plastic washers.

Step 10

              Remove drive gear
  • Using a punch and a hammer push out the pin. (Note: support the gear on the opposite side to protect the the motor shaft from damage).
  • The gear ist free.
  • When inserting the pin, support the gear on the opposite side to protect the the motor shaft from damage.

Using a punch and a hammer push out the pin. (Note: support the gear on the opposite side to protect the the motor shaft from damage).

The gear ist free.

When inserting the pin, support the gear on the opposite side to protect the the motor shaft from damage.

To reassemble your device, follow these steps in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.                                             


        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 2 other contributors 


                    Dominik Kübelsbeck

Member since: 07/08/2019

279 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Rainer Jourdan - Mar 30, 2020

Reply

super Anleitung

hat problemlos geklappt

vielen Dank.

PS: ist schon ein bisschen aufwendig, nur um den Antriebszahn zu wechseln, die gesamte Maschine zu zerlegen.

Gruß Rainer

landrieu - Apr 11, 2020

Reply

Great tutorial, however it does not apply for me, as I have a Kenwood titanium KMY60 model, this spare part does NOT have a pin. I can’t say how it is fixed to the gear, could you advice on how to disassemble it?

Christian Bolleter - Jan 14, 2022

Hi, how did you manage to disassemble the part without the pin? How is it fixed? Thank you!

Andre2111 - Jun 5, 2020

Reply

vielen Dank für die Anleitung. Hat (fast) alles funktioniert, außer das Kabel für das Licht. Es rutscht beim Einsetzen des Oberteils immer wieder ab. Gibt es einen besonderen Tip?

Niels Rütthard - Jul 15, 2020

Reply

Danke für die Anleitung. Wir haben angefangen, nach Gutdünken loszuschrauben und sind kläglich gescheitert. Mit der Anleitung hat es geklappt. Vielen Dank dafür!

Ich bin selber Ingenieur und konstruiere mechanische Bauteile und bin doch sehr verwundert, das Kenwood dermaßen kompliziert baut.