Difficulty

Easy

Steps

8

Time Required

                          30 minutes

Sections

1

  • Kambrook KCE75 Heater Disassembly
  • 8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackKambrook KCE75 Heater

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Phillips head screw driver (20cm-40cm)

Flat head screw driver or prying tool

2x Needle nose plyers

Have a dirty or broken heater and what to do something about it?

Heres the perfect step by step guide to disassemble your kambrook heater and rectify the issues along the way.

Step 1

              Main housing shell disassembly
  • 4 x phillip screws located in the rear
  • Phillips head screw driver required
  • Remove the screw and take apart the top cover facing upwards
  • 2 wires are attatched to the top housing

4 x phillip screws located in the rear

Phillips head screw driver required

Remove the screw and take apart the top cover facing upwards

2 wires are attatched to the top housing

1024

Step 2

              Fan shroud disassembly
  • 4x Phillips screws
  • Phillips head screw driver required
  • The front grill should fall out after screws are removed

4x Phillips screws

The front grill should fall out after screws are removed

Step 3

              Switches Disassembly
  • Remove the switches that are attatched to the main shell
  • Using Needle nose plyer unclip the negative (black) cable first, then the red
  • Both switches have the same connecting plugs
  • The plugs of the swithces should have no corrision or wear, replace if cable if freyed or torn

Remove the switches that are attatched to the main shell

Using Needle nose plyer unclip the negative (black) cable first, then the red

Both switches have the same connecting plugs

The plugs of the swithces should have no corrision or wear, replace if cable if freyed or torn

Step 4

              Main Housing disassembly
  • Phillips head screw driver required
  • 4 phillips head screws are holding the plastic housing to the shell
  • Unscrew the 4 screws and remove the housing by hand
  • Heater should not have burn marks or heat damages, replace if damag is visible

4 phillips head screws are holding the plastic housing to the shell

Unscrew the 4 screws and remove the housing by hand

Heater should not have burn marks or heat damages, replace if damag is visible

Step 5

              Heater Core Disassembly
  • This step requires a flat head or a pry tool
  • There are 4 tabs holding the heater core in place
  • Another 4 tabs that connects to the thermo switch
  • Pry the pins where the tab meets the connector plugs
  • Replace Pins if wires are freyed or damaged

This step requires a flat head or a pry tool

There are 4 tabs holding the heater core in place

Another 4 tabs that connects to the thermo switch

Pry the pins where the tab meets the connector plugs

Replace Pins if wires are freyed or damaged

Step 6

              Fan Assembly
  • 2 Phillips head screw are holding the motor and blade in place
  • Phillips head Screw drive required
  • From the rear unscrew the 2 screws
  • Removed the motor and fan from the front
  • Disconnect the wires piror to pulling the moto out

2 Phillips head screw are holding the motor and blade in place

Phillips head Screw drive required

From the rear unscrew the 2 screws

Removed the motor and fan from the front

Disconnect the wires piror to pulling the moto out

Step 7

              Disconnecting Aux
  • Needle nose plyers and pry tool/flat head are required for this step
  • Micro switch is connected with a tab plug.
  • Using a small flat head or pry tool, release the tab from the switch
  • Leave the thermostat connected

Needle nose plyers and pry tool/flat head are required for this step

Micro switch is connected with a tab plug.

Using a small flat head or pry tool, release the tab from the switch

Leave the thermostat connected

Step 8

              Disasembly
  • Insert wisdom here.

Insert wisdom here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Ken Pang

Member since: 04/25/2020

157 Reputation

                                      1 Guide authored                  



                       Badges:
                       1