Difficulty
Moderate
Steps
9
Time Required
30 - 35 minutes
Sections
1
- The Power Button
- 9 steps
Flags
0
BackJVC XL-333 CD Player
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
The Power Button
- Using your Phillips Head Screwdriver, remove the four screws with the red markup.
- Then, remove the three orange screws using your screwdriver.
Using your Phillips Head Screwdriver, remove the four screws with the red markup.
Then, remove the three orange screws using your screwdriver.
1024
Step 2
- Remove the two Phillips screws on both sides of the CD Player.
Remove the two Phillips screws on both sides of the CD Player.
Step 3
- Remove the top of the CD Player by holding each side of the roof then sliding it away from the front of the CD player.
Remove the top of the CD Player by holding each side of the roof then sliding it away from the front of the CD player.
Step 4
- The disk reader is located above the power button.
- Push out these tabs on both sides of the disk reader.
The disk reader is located above the power button.
Push out these tabs on both sides of the disk reader.
Step 5
- Unscrew the four Phillips copper screws located at the four corners of the disc reader.
- After the screws are removed, gently pull the disc reader up and out of the CD player.
Unscrew the four Phillips copper screws located at the four corners of the disc reader.
After the screws are removed, gently pull the disc reader up and out of the CD player.
Step 6
- Gently pull up to remove the two bunches of wires with a green connector from the motherboard.
- Remove the two groups of wires with a white connector by using your spudger or tweezers to pull up on the side of the connector, opposite of the wires. It may require some force
Gently pull up to remove the two bunches of wires with a green connector from the motherboard.
Remove the two groups of wires with a white connector by using your spudger or tweezers to pull up on the side of the connector, opposite of the wires. It may require some force
Step 7
- These pictures offer other tricks and guidance on how to remove the wire connectors.
- move your spudger or tweezer in an upward motion to release the wires.
These pictures offer other tricks and guidance on how to remove the wire connectors.
move your spudger or tweezer in an upward motion to release the wires.
Step 8
- Remove the rest of the wires connecting the motherboard to the CD player with your spudger or tweezers.
- Remove the screw that connects the wire to the motherboard.
Remove the rest of the wires connecting the motherboard to the CD player with your spudger or tweezers.
Remove the screw that connects the wire to the motherboard.
Step 9
- Find the power button trigger on the left side of the CD Player. It should be gray.
- Push it a couple times to make sure it works. If not hold it 3/4 of the way and pull with some force.
- Replace with a new one.
- Replace the motherboard, reattach the cables and repeat the rest of the previous tasks in reverse.
Find the power button trigger on the left side of the CD Player. It should be gray.
Push it a couple times to make sure it works. If not hold it 3/4 of the way and pull with some force.
Replace with a new one.
Replace the motherboard, reattach the cables and repeat the rest of the previous tasks in reverse.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Romenick Casabar
Member since: 06/01/2016
110 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Central Coast New Tech High, Team 5-4, Rushing Spring 2016
Member of Central Coast New Tech High, Team 5-4, Rushing Spring 2016
CCNTH-RUSHING-S16S5G4
2 Members
1 Guide authored
